0
Your 4 yr old rca tv is taking a long time to turn the power button blinks 3 times almost like a code?
it is leakage in your cp150 120& 114 capacitors located on the flb circuit board should be green capacitors. with gold writing if bulged they are leaking if u can locate them heat them up with hair dryer for a couple minutes then power on t.v. usually works i did then just leave tv on u can buy these capacitors at tv repair world.com along with instructions for about $25.00
What else can I help you with?
How do I scan a picture from my hp deskjet f4100 printer every time I press scan the power button just blinks until I press cancel what do i do?
mine does the same thing, it used to work.
How do i Program a vizio sound bar to comcast remote?
After much research, here is a step-by-step for getting your Vizio Soundbar to work with the Comcast remote using EFC codes (mine is the newer charcoal grey one, works great!) Aux - Setup (2 blinks) - 11144 (2 blinks) Aux - Setup (2 blinks) - 994 - Setup - 00169 - Vol Up - Should get 2 blinks Aux - Setup (2 blinks) - 994 - Setup - 00168 - Vol Down - Should get 2 blinks Aux - Setup (2 blinks) - 994 - Setup - 00037 - Mute - Should get 2 blinks Aux - Setup (2 blinks) - 994 - Setup - 00165 - Power - Should get 2 blinks Aux - Setup (2 blinks) - 994 - Setup - 00164 - Input - Should get 2 blinks These are optional, I didn't use them: Aux - Setup (2 blinks) - 994 - Setup - 00036 - <button to use for TVOL> - Should get 2 blinks Aux - Setup (2 blinks) - 994 - Setup - 00101 - <button to use for TSHD> - Should get 2 blinks Then set the volume control on the remote and other settings according to the Remote's manual. ENJOY!! Hope this helps someone...
How do you program a sears 139.53859 garage door opener?
If you want to add a remote, press the "set" button on the power unit until the green light blinks, then press the button on the remote. If you want the unit to forget all old codes and accept only the new remote, hold the "set" button until the green light stays on solid, then press the remote button.
How can I reprogram my ceiling fan remote?
To reprogram your ceiling fan remote, first, turn off the power to the fan. Then, locate the reset button on the remote and press it. Next, press and hold the reset button on the fan itself. Release the buttons when the fan light blinks. Your remote should now be reprogrammed.
Why does your Nintendo DS blink?
It blinks if your DS is on and closed. It tells you that your power is on, but your not using it- Saving Energy/DS Power!
How can I reset my Hunter fan remote?
To reset your Hunter fan remote, you can usually press and hold the fan's power button for about 5-10 seconds until the light on the remote blinks. This should reset the remote and allow you to reprogram it as needed.
How can I reset a Hunter fan remote?
To reset a Hunter fan remote, you can usually press and hold the fan's power button for about 5-10 seconds until the light on the remote blinks. This should reset the remote and allow you to reprogram it as needed.
Why is the green light flashing on my PS3?
The PS3's power indicator blinks when you turn off the system to tell you it's shutting off. As you probably know, the blue light indicates that a disc is in the drive and the red light is when the PS3 is off and in standby mode. A constant green blinking light could mean some problem occurred and it is taking longer than normal to shut off, if it doesn't turn off, hold the front power button down for 10 seconds to turn it off. You may then have to turn the PS3 on again with the same button as the PS button on the controller may not turn it back on.
Monitor power button switch working but power is not out put in the monitor?
if it says power button locked hold "<" button and power button till the message goes.(at least a min)
What is Verizon fios remote code for vizio sound bar?
Couldn't find one for mine - the uverse remote just isn't that flexible. I bought a Logitech Harmony 650 remote for $70 on Amazon. Took a few minutes to setup, then it worked liked a charm instantly! Best $70 I ever spent.
What to do when there is error that says power button lock out on the monitor?
Press, and hold the power button for 10 seconds to unlock the power button.
Why won't my hp notebook turn on the light for the on button blinks But does not turn on?
In most cases your HP notebook is in "power saving" mode. Please make sure your notebook is plugged into a power source as the battery could the result of the "blinking" ON button. If the battery is low, the computer will not turn on and will stay in "sleep" mode. If this is not the case, simply press and hold your power button that is blinking for 5-10 seconds. You will see your computer turn-off. Press the power button again (*given that the steps above have been followed through) and your computer light should turn back on and remain solid. If for some reason you find that the "ON" button light is constantly blinking, but the HP notebook is not turning on, make sure that your battery is not dead, and your power supply (the actual power cable and black power bar) is working.
