0
If the headlights on your 2001 Pontiac Aztek won't turn off, it could be due to a faulty headlight switch, a stuck relay, or an issue with the body control module. Check the headlight switch and try turning it off and on again. If that doesn't work, inspect the relay in the fuse box or consider disconnecting the battery to reset the electrical system. If the problem persists, it may be best to consult a mechanic for further diagnosis.
What else can I help you with?
Is there a fuel shut off switch on a Pontiac aztek?
Where is the fuel shut off on 2002 aztek
When AC is on car smokes under the hood does not smoke when the AC is off 2001 Pontiac Aztek?
Check the driver belt, tensioner and the a/c clutch and compressor.......
How do you reset computer for a 2001 Pontiac Aztek?
to reset the computor..all you have to do is take the negative battery cable off for about 10 min. then tighten back on. tada!
Where can i buy a tent for a 2003 Pontiac Aztek?
Ebay. Type in the Pontiac Aztek and all the parts and accessories that everyone have for sale pop up. I bought my console cooler off of Ebay.
How do you change a serpentine belt for a Pontiac aztek?
Removing the serpentine belt on a Pontiac Aztek requires loosening the adjustment pulley. Once the pulley is loose the serpentine will have enough slack to come off.
Dose a 2001 Pontiac aztek have back air brakes?
Umm... i think you are referring to the air self levelling system which levels the aztek according to the load. When you shut off the vehicle you will hear the air release after a few minutes. i believe that is what you are hearing.
How do you replace a serpentine belt on Pontiac Aztek?
This link has many helpful diagrams. There should also be one under your hood by the belt labeled Accessory Drive Belt Routing. So if you find the diagram on your car you can match it to the diagram in this link and it will even tell you what to loosen to get the belt off. http://www.2carpros.com/car_repair_information/tec_info/2001/pontiac/aztek/2001_pontiac_aztek_drive_belt_routing_diagram.htm
How do you replace the front o2 sensor on a 2001 Pontiac Aztek?
To replace the front O2 sensor on a 2001 Pontiac Aztek, first, ensure the engine is off and cool. Locate the sensor on the exhaust manifold and disconnect the electrical connector. Use an O2 sensor socket or a wrench to unscrew the old sensor, then install the new sensor by threading it in and tightening it securely. Finally, reconnect the electrical connector and start the engine to check for proper operation.
How do you remove the radio in a 2001 Pontiac aztek?
To remove the radio in a 2001 Pontiac Aztek, first disconnect the negative battery cable to ensure safety. Use a trim removal tool to carefully pry off the trim panel surrounding the radio, then remove any screws securing the radio in place. Slide the radio out from the dashboard and disconnect the wiring harness and antenna cable at the back. Once everything is disconnected, the radio can be fully removed.
How do you remove the drum on 2001 Pontiac aztek?
To remove the rear drum on a 2001 Pontiac Aztek, first ensure the vehicle is securely lifted and supported. Remove the wheel and tire, then locate the drum mounting screws, if present, and remove them. Use a rubber mallet to gently tap around the drum to loosen it, and then pull it off the hub. If it’s stuck, check for any retaining clips or adjust the brake shoes inward before attempting to remove the drum.
How do you change licenseplate light bulb on 2001 Pontiac aztek?
To change the license plate light bulb on a 2001 Pontiac Aztek, first, open the rear hatch to access the light assembly. Use a flathead screwdriver to gently pry off the lens cover. Once the cover is removed, twist the bulb socket counterclockwise to release it, then pull out the old bulb and replace it with a new one. Finally, reinsert the bulb socket, replace the lens cover, and ensure everything is securely in place.
How do you replace oil pump on a 2001 Pontiac aztek?
To replace the oil pump on a 2001 Pontiac Aztek, first disconnect the battery and drain the engine oil. Remove the oil pan by unbolting it from the engine block, which may require lowering the exhaust or other components for clearance. Once the oil pan is off, unbolt the old oil pump from the engine and replace it with the new one, ensuring to use a new gasket. Finally, reassemble the oil pan, refill the engine with oil, and reconnect the battery.
