0
What else can I help you with?
How do you install the distributor on a 1998 Nissan Pathfinder?
mark position of old distributor on motor and on old dist, also mark position of rotor. Remove old distributor, mark the position on new distributor, move rotor to the marked position, drop in
Where is the camshaft position sensor switch located on your 1995 Durango?
The Dodge Durango was introduced in 1998, so this question cannot be answered. However, in the 2000 Durango.... The camshaft position sensor is located in the distributor on all 3.9L V-6 and 5.2/5.9L V-8 engines Camshaft Position Sensor REMOVAL Distributor removal is not necessary to remove camshaft position sensor Remove air cleaner assembly. Disconnect negative cable from battery. Remove distributor cap from distributor (two screws) Disconnect camshaft position sensor wiring harness from main engine wiring harness. Remove distributor rotor from distributor shaft. Lift the camshaft position sensor assembly from the distributor housing Camshaft Position Sensor INSTALLATION Install camshaft position sensor to distributor. Align sensor into notch on distributor housing. Connect wiring harness. Install rotor. Install distributor cap. Tighten mounting screws. Install air cleaner assembly. (this info from post on answers.com about cps on 2000 durango)
Where do you install the crank position sensor in a 1996 e350 ford bus?
If it has a distributor it doesnt have a crank position sensor. The magnetic pickup in the distributor is what you would be looking for. The module is either on the side of the distributor or on the firewall against the drivers inner fender.
Will a distributor spark if it is not in the correct position?
That's not really what's going on. The coil makes the spark, the distributor distributes the spark to the correct plug. If the distributor is not in the correct position, the spark does not go to the correct plug, or goes to the correct plug at the wrong time.
How do you install 1993 rodeo distributor?
install distributor rodeo 1993
Where is the camshaft position sensor located on a 1999 Dodge Durango?
It's located on the distributor. You don't have to remove the distributor to replace the sensor. Remove the air cleaner, disconnect the negative battery cable, remove the distributor cap, disconnect the camshaft position sensor wiring harness, remove the distributor rotor, lift the camshaft position sensor assembly from the distributor housing Camshaft Position Sensor. Installation, Install the camshaft position sensor into the distributor. Align the sensor into the notch on the distributor housing, connect the wiring harness, reinstall the rotor, reinstall the distributor cap. Tighten the mounting screws, reinstall the air cleaner.
How do you install distributor in a 2000 ford ranger with 3.0 engine?
To install the distributor in a 2000 Ford Ranger with a 3.0 engine, first disconnect the negative battery cable and remove any components obstructing access to the distributor. Align the engine to top dead center (TDC) on the compression stroke for cylinder one, then remove the old distributor and carefully note the rotor's position. Install the new distributor, ensuring the rotor aligns with the same position as the old one, and secure it in place. Finally, reconnect any removed components and the battery cable.
How do you install a distributor in a Chevrolet s10 2.5?
To install a distributor in a Chevrolet S10 2.5, first remove the old distributor by marking its position and disconnecting the wiring and vacuum lines. Align the new distributor so that the rotor points to the same position as the old one, then carefully lower it into the engine, ensuring the oil pump drive engages. Reconnect the wiring, vacuum lines, and secure the distributor with the hold-down clamp. Finally, double-check the timing and make any necessary adjustments.
How do you remove hall effect sensor in 1998 vw jetta?
First remove distributor cap. loosen the bolt that holds down distributor and take holding plate of MAKE SURE YOU MARK DISTRIBUTOR POSITION AGAINST BLOCK AND ROTOR AGAINST DISTRIBUTOR HOUSING. pull out distributor from engine. now take out the pin that holds the gear on the distributor rotor shaft take the gear of the shaft, position of gear on shaft is not important. now from the the top of the distriburator pull the rotor shaft out and wow la. camshaft position sensor is ready to be taken out. To install just reverse the steps and when you ready to install the gear on shaft make sure that the gears is against the distributor housing and not on the tip of the shaft (up side down). installing distributor on engine. install the the rotor on shaft and turn it about 20 degrees clock wise so when you push the distributor into the engine is going to turn back to the original position. You are welcome jcdl. 7-10-08
How do you put distributor in 2002 blazer 4.3?
how to install a distributor
How do i install a 1997 dodge caravan 3.0 camshaft position sensor?
If I'm not mistaken, I think the camshaft position sensor on these engines is built into the distributor. You'd have to replace the whole thing.
How do you replace the distributor on a Nissan pickup D21 1996?
To replace the distributor on a 1996 Nissan D21 pickup, first disconnect the battery and remove any components obstructing access to the distributor. Mark the position of the existing distributor and the ignition wires for reference, then remove the distributor cap and rotor. Unscrew the distributor hold-down bolt, lift the distributor out, and install the new one in the same position. Reconnect the ignition wires, replace the rotor and cap, and reconnect the battery to complete the installation.
