0
What else can I help you with?
Why do struts go out?
Struts wear out on a car because they tend to rust. A person that does a lot of winter driving will probably have to replace struts in a car once while it is owned, if kept for a long time.
How do you replace the trunk struts on my sc300 Lexus?
To replace the trunk struts on your Lexus SC300, first, ensure the trunk is supported to prevent it from falling. Use a flathead screwdriver to gently pry off the retaining clips on each end of the struts. Once the clips are removed, detach the old struts from the mounting points and replace them with the new struts, ensuring they are securely attached. Finally, reattach the retaining clips to complete the installation.
How do you replace the front struts on Hyundai Sonata 2000 model?
To replace the front struts on a 2000 model Hyundai Sonata, you will first need to remove the tires. There will be 3 nuts on top of the strut mount. You will need to remove the 2 bolts that connect from the strut to the knuckle. Then you will need to remove the ABS sending unit as well as the front brake hose. Once these components are removed, you can remove the strut. In order to remove the strut, you will need a special tool to compress the spring. Once the struts are removed, you can safely replace them with new struts.
How hard is it to replace struts?
It isn't hard at all aslong as you have patience and alittle know how. Be warned I highly suggest you take the struts once removed from the car to a service center to have them remove the strut from the springs!
How do you replace struts on 96 olds 98 regency?
If you don't have the right tools don't attempt to change your struts. Getting the struts of is, easy but you have to have a spring compressor once you get them off also you need a workbench with a vice to remove the spring. Very Dangerous without proper tools.
Why would the front wheel hop on your 96 blazer when going over bumps?
It sounds like it could be a bad strut. Push down quickly and firmly on the front of the vehicle, if the car bounces more than once or twice you may need to replace your struts.
How does one replace a car steering wheel cover?
You can replace a steering wheel cover by first removing the old steering wheel. Once complete, wash and dry clean the steering wheel and then apply your new steering wheel cover.
How do you replace front wheel bearing 1992 k1500 Chevrolet?
i may be wrong, but if i recall correctly from high school automotives the wheel bearing has to stay with the wheel it was built for so you have to replace the whole wheel once again though i am not 100% on this
How do you replace rear struts on 91 olds 98?
To replace the rear struts on a 1991 Oldsmobile 98, start by safely lifting the rear of the vehicle and securing it on jack stands. Remove the rear wheels, then unbolt the lower strut mount and the upper strut bolts from the inside of the trunk. Once the old struts are removed, install the new struts by reversing the process, ensuring all bolts are torqued to the manufacturer's specifications before reattaching the wheels and lowering the vehicle. Always check for proper alignment and functionality after completing the installation.
How do you replace the steering wheel radio and cruise control buttons on a 1999 Lincoln town-car your buttons have melted?
replace the whole steering wheel cause once the buttons have melted??...they wont work anyway.
How do you replace front struts 2002 Buick Lesabre?
To replace the front struts on a 2002 Buick LeSabre, begin by safely lifting the vehicle and removing the front wheels. Next, disconnect the sway bar link and the lower bolt from the strut assembly, then remove the upper strut mount bolts from the engine compartment. Once the strut is free, replace it with the new strut, reassemble the components in reverse order, and ensure everything is tightened to the manufacturer's specifications before lowering the vehicle back to the ground. Always consider having an alignment done after replacing struts.
How do youm replace the fly wheel on a 1988 Chevy Suburban with 5.7 liter engine?
The transmission has to be removed. Once the trnsmission is removed the fly-wheel is right there to be removed.
