answersLogoWhite

0

Yes, there are about 6 bolts on each side you have to remove, you do not have to remove the molding, just use the access panels, however you have to pull the center part out, (3000GT part) a bit to remove the tail light.

User Avatar

Wiki User

18y ago

What else can I help you with?

Related Questions

How to replace front turn lights an front side lights on 2001 Mitsubishi Montero?

I had the same problem once and saved alot of money by doing it myself. You could remove the entire (or part) of the fender cover (under the fender) until you get access to the light housing. All you will need to do is unscrew the light and pull it out. The hardest part was getting access.


How do you replace tail lights and blinkers in a 1997 Chevy?

Drop the tailgate, access the screws to remove the taillight assembly. Remove the screws holding the circuit board to the assembly, pull the board and you will have access to the bulbs.


When you replace a headlight, does it automatically replace your emergency lights?

Each type of vehicle has a unique design to its headlight assembly. Some have the headlight and emergencey lights in one housing others have them seperated.


How do you repair tail lights on Volvo 240?

To repair tail lights on a Volvo 240, first, access the tail light assembly by opening the trunk and removing the screws or clips securing the light housing. Disconnect the wiring harness and remove the old bulb by twisting it counterclockwise. Replace it with a new bulb, reassemble the housing, and reconnect the wiring harness. Finally, test the lights to ensure they are functioning properly before securing everything back in place.


How do you change housing fog lights on Toyota Tundra 2004?

To change the housing fog lights on a 2004 Toyota Tundra, first, ensure the vehicle is turned off and the keys are removed. Access the fog light assembly by removing the screws or clips securing the cover. Disconnect the wiring harness from the old fog light and replace it with the new one, then reassemble the cover and secure it back into place. Finally, test the new fog lights to ensure they are functioning properly.


How do you replace head lights 1999 maxima?

Headlight Bulb Replacement * Open the hood and locate the bulb assembly on the back of the headlight housing.On the right side headlight remove the two screws and the plastic shield for access to the bulb * Unplug the electrical connector and detach the retaining ring * Withdraw the bulb assembly from the headlight housing * Without touching the glass with your bare fingers insert the new bulb into the assembly Headlight Housing Replacement* Disconnect the negative battery cable * Remove the headlight bulb * Remove the radiator grille * Remove the parking light housing * Remove the retaining nuts and bolts detach the housing and withdraw it from the car


How do you change the brake lights on a 2002 Mitsubishi Eclipse?

You must open the hatch, remove the plastic strips then you must unbolt the tail lamp assembly and remove the bulb.


How do you change the brake lights in a 1993 Ford Thunderbird?

Entire assembly should unbolt and slide out giving access to the bulbs


What are the two lights in the Mercedes E320 wagon headlight assembly and how do you remove the lights?

The two lights in the Mercedes E320 wagon are the low and high beam bulbs. they can be accessed through the engine compartment. This bulbs just twist off the headlight housing.


How do you replace the headlight assembly located on a Suzuki Sidekick Sport?

The lights on the Sidekick simply twist out from the rear of the fixture. Open the hood, unplug the wiring assembly, and twist the light bulb assembly about a 1/4 turn. You can then pull the light from the headlamp housing.


How do you replace fog lights in a 2008 Mercury Mariner?

To replace the fog lights in a 2008 Mercury Mariner, first, ensure the vehicle is turned off and the keys are removed. Access the fog light assembly by removing the screws or clips that secure it, typically located behind the fog light housing. Disconnect the wiring harness, then remove the old bulb by twisting it counterclockwise. Insert the new bulb, reconnect the wiring harness, and reassemble the fog light assembly.


What is the yellow wire with a black stripe for 2000 Mitsubishi galant for panel lights?

where does the yellow wire with a black stripe on it connect for dimmer lights,panel lights,and gear shift lights,for a 2000 Mitsubishi galant