HOW do you replace the distributor stator pickup on a 1995 Ford F-250 with a 460 engine?

Do you have to remove the distributor to replace the stator in a 90 Chevy 350?

Yes you do. You have to take the distributor shaft out of the distributor to Remove the pick-up coil / stator.

How do you change stator on honda foreman 450?

To change the stator on a Honda Foreman 450, first disconnect the battery and remove the side cover to access the stator. Carefully disconnect the stator wires and unbolt the stator from the engine. Replace it with the new stator, reattach the wires, and secure it with the bolts. Finally, replace the side cover and reconnect the battery to complete the installation.

Where is the stator on a 1991 Mercury Capri?

near the distributor cap

How do you change a pickup coil in a 1988 Ford Ranger?

1)Rotate the engine until the No 1 piston is on Top Dead Center TDC of its compression stroke. The timing marks on the crank shaft and the pointer are aligned. 2)Disconnect the negative battery cable. Disconnect the wiring harness from the distributor. Mark the #1 spark plug tower on the cap for reference. 3)Remove the distributor cap. Matchmark the rotor position to the distributor housing. Scribe a mark in the distributor body and the engine block to indicate the position of thedistributor in the engine. 4)Remove the distributor hold-down bolt and clamp - Remove the distributor from the engine. Do not rotate engine while the distributor is removed. 5)Remove the two screws going through the plastic cover. Remove PIP unit, and replace with a new one. These are normally light tan in color - if it looks burnt - darkened it is probably defective. Or the Hall Effect vane stator switch assembly. 6)Before reinstalling the distributor - rotate the distributor shaft so the rotor points toward the mark on the distributor housing made previously. Rotate the rotor slightly so the leading edgeof the vane is centered in the vane switch state assembly. Rotate the distributor in the engine block to align the leading edge of the vane with the vane switch stator assembly. Make sure the rotoris pointing to the No 1 mark on the distributor base. If things don't line up raise the distributor just enough to disengage it from the gear and rotate it to engage another gear tooth. Note: some require removing the gear from the shaft to replace the PIP. Remove the drift pin from the gear - clean the shaft with emory cloth and then you can replace the ignition parts.

How do you replace stator on 50 hp evinrude?

To replace the stator on a 50 hp Evinrude outboard motor, first disconnect the battery and remove the engine cover for access. Then, locate the stator, which is typically mounted on the flywheel side of the powerhead. Remove the flywheel by loosening the flywheel nut and using a puller if necessary, then unscrew the stator mounting bolts and disconnect the wiring harness. Install the new stator by reversing these steps, ensuring all connections are secure before reassembling the engine cover and reconnecting the battery.

How do you replace the pickup coil on a 1995 Ford Taurus?

remove the distributer, remove the roll pin holding the drive gear onto the distributer shaft, remove the distributer drive gear, remove the shaft from the distributer to gain access to and remove the stator(pick-up coil). Replace the stator, and reassemble everything.

Where is the pickup coils located on 2003 Honda vtx1300cc motorcycle?

On a 2003 Honda VTX 1300cc motorcycle, the pickup coils are located on the left side of the engine, near the stator. To access them, you'll typically need to remove the left side cover and possibly the stator cover. The pickup coils are responsible for generating the signal for the ignition system. Ensure to follow proper service procedures when handling these components.

Why does your 1988 Dodge Aries start up on the gas it get when you turn the key on but then stall because the injector doesn't pump any gas after that?

This could be due to a bad Hall effect sensor. On this car it is part of the pickup coil/stator. This can be found under the distributor cap and rotor, and is the piece that the wire goes into. The pickup coil senses the magnetic field as pieces of metal are rotated through the Hall effect sensor. This device controls the fuel delivery of the car after it has started and is generally a big culprit for a stalled Dodge Aries. To replace you will need to remove the distributor cap and rotor. The pickup coil will be under those and rather simple to replace. It costs about $25-$40.

What side of a polaris engine is the stator located on?

In a Polaris engine, the stator is typically located on the flywheel side, which is the side opposite the transmission. This positioning allows the stator to generate electrical power as the flywheel spins. The stator is an essential component of the engine's ignition and charging systems.

Ford f 250 was running great then shut off can restart but only for 5 seconds before it turn off?

I had a similar problem. My solution was to replace the distributor's stator - part of the breakerless ignition. My stator's plastic housing had cracked which caused an intermitant shorting of the ignition system.

Where is stator on 1990 evinrude?

The stator on an Evinrude outboard is located under the engine flywheel.

How do you get the stator out of a 750 Kawasaki vulcan engine?

To remove the stator from a 750 Kawasaki Vulcan engine, first disconnect the battery and remove any necessary covers to access the stator. Then, detach the stator’s wiring harness and unscrew the bolts securing the stator to the engine case. Carefully lift the stator out, ensuring you don’t damage any surrounding components. Always refer to the service manual for specific torque specifications and procedures.