answersLogoWhite

0

To wire up a ready-to-run distributor, first ensure the engine is off and the battery is disconnected. Connect the ignition coil's positive terminal to the distributor's power terminal, and attach the negative terminal to the coil's negative terminal. Then, connect the distributor's output wire to the appropriate cylinder's spark plug wire. Finally, ensure all connections are secure and reconnect the battery before starting the engine.

User Avatar

AnswerBot

2mo ago

What else can I help you with?

Related Questions

How do you wire up a distributor from a 1982 Oldsmobile 88 350 ci?

18436572


Could some one help could you tell you where the tachometer connection is on a 1991 Chevy s10 4.3 Leter is on the distrubutor with the four wire or the two wires?

Green wire on the distributor is the tachometer pick up. Green wire on the distributor is the tachometer pick up.


Where does spark come from on a 90 dodge ram 318?

The computer uses the pick up plate in the distributor to know when to activated the coil to cause a spark to go down the coil wire to the distributor cap and through the cap and rotor to an individual plug wire to the spark plug.The computer uses the pick up plate in the distributor to know when to activated the coil to cause a spark to go down the coil wire to the distributor cap and through the cap and rotor to an individual plug wire to the spark plug.


How do you wire up an electronic distributor from points distributor its a 4y toyota 2.2 motor?

To wire up an electronic distributor for a 4Y Toyota 2.2 motor, first remove the old points distributor and ensure the new electronic distributor is properly installed in the engine. Connect the ignition coil’s positive terminal to the power source, typically the ignition switch, and the negative terminal to the electronic distributor's signal wire. Ground the electronic distributor to the engine block for proper function. Finally, ensure all connections are secure and verify the timing before starting the engine.


How2 hook up sun super tach 2 to a 88 k5 blazer?

u have to look at ur distributor if it is an HEI "coil on top there is markings on the distributor cap for the tach but if it is a regular distributor with an external coil you hook it up to the neg wire off the coil neg/ black wire


How do you wire up a factory tach in a 1986 Pontiac Grand Prix?

The tach should connect to the distributor.


How do you wire a Chevy 305 in a 82 cutlass v6?

distributor wire to the distributor red and brown to the starter alternator hook up is the same on the v 6 and the 305 all located on left side of wiring harness coming out the fire wall and you will have to have a vacum advane distributor to bypass computer


Where can you get the basic ignstarting system diagram to start up your 1986 gmc 350 at just th ebasic diagram to start your project truck thanks?

Most basic way to start it. Run a hot wire to the Batt terminal on the distributor, where the wires connect on the side of the distributor it should be a square projection on the side of the cap. The Batt. wire should be the right hand one as you look at it. Power to this wire and arc the starter. An 86 should be carburated so you don't need to worry about the computer. The truck will run but you will not have the rest of the electrical system, the alternator will not charge, this is just to run the motor.


Where to connect hot wire from distributor electric ignition on 1953 Chevy pick up?

Question is confusing. Original wiring, power to the plus side of the coil, minus side of coil to the distributor. If you have put an electronic HEI distributor in then eliminate the coil and take the plus side wire and connect to the HEI.


How do you change your Oldsmobile points distributor to a HEI and not mess up the timing?

It's the same on a Chevy pull your distributor cap see what position the rifle buld is facing and drop the electronic dust. In the same position and wire it up and add an ignition power to the distributor.


How do you hook up tachometer to a Chevy 350 that does not have HEI distributor?

Connect the green wire to the negative side of the coil.


How do you hook up two car stereo amplifiers one to each sub in there own box can you run a power wire out of one amp over to the other amp?

Do you mean the main power from the battery or the remote turn on? If you mean the battery power, usually amp add on kits come with distributor blocks. You make one run of power wire from the battery to somewhere close to your amps. Then, hook that wire to the block, and run a new piece of wire from the block to each amp. If you mean the turn on lead, just make one run from the head unit to the first amp, and then run another piece from the first amp to the second.