0
if it's a foam filter , clean with dish soap, when it dries put a little motor oil on it and sqeeze out excess, you want a very light coating of oil throughout filter it helps trap dirt. if it's a paper filter you can't really clean them, they are available at most home stores if the square type, about 5 dollars
What else can I help you with?
Why does a Briggs and Stratton 11hp engine quit after starting?
Could be plugged fuel filter, sticking float:Change fuel filter, clean carb.
Why does a Briggs and stratton 12.5 HP lawn mower engine stop 2 3 seconds after it starts?
Check fuel filter or sticking float: replace filter clean carb. hope this helps
How do you tune up 4 hp Briggs and stratton?
To tune up a 4 HP Briggs and Stratton engine, start by changing the oil and replacing the oil filter if equipped. Next, clean or replace the air filter and spark plug to ensure optimal combustion. Check the fuel system for any debris and replace the fuel if it's old. Finally, inspect the carburetor and adjust the throttle and idle settings as needed for smooth operation.
How do you clean float needle on 16.5 HP Briggs and Stratton Engine?
To clean the float needle on a 16.5 HP Briggs and Stratton engine, first, remove the carburetor from the engine. Disassemble the carburetor to access the float and needle assembly, then carefully remove the float and needle. Clean the needle and seat with carburetor cleaner and a soft brush to remove any debris or varnish. Reassemble the components and reinstall the carburetor, ensuring all connections are secure.
How do you clean a 3.5 hp Briggs and stratton carburetor the self propelled Yardmaster. It WONT start even after changing spark gas air filter.?
check your coil out
Why does a Briggs and stratton quattro petrol engine lawnmower stop 4-5 seconds after starting?
I would start with float sticking or maybe fuel filter plugged filter and run some good carb cleaner threw a tank of fuel if that does not fix your problem you may have to take the carb apart and clean it.
Where do you find the stamped engine number on Briggs and stratton 10hp ohv?
The stamped engine number on a Briggs and Stratton 10hp OHV engine is typically located on the engine's side, near the air cleaner or on the engine block itself. You may also find it on a metal tag attached to the engine. Look for a series of numbers and letters that indicate the model, type, and code date. Always ensure the engine is clean for easier visibility of the stamped number.
When checking the oil level on a Briggs and Stratton engine should the dipstick be screwed down or just pushed in?
When checking the oil level on a Briggs and Stratton engine, the dipstick should be just pushed in without screwing it down. This allows you to get an accurate reading of the oil level. After removing the dipstick, wipe it clean before reinserting it to check the level again. Always ensure the engine is on a level surface for the most accurate measurement.
Why does your Briggs and stratton quantum xm 4 hp engine start but not keep running?
Clean out the carburetor with gas, the reason it wont keep running is its not getting enough gas through the carburetor.
My 5hp Briggs an stratton will not stay started?
If your 5hp Briggs & Stratton engine won't stay started, it could be due to several issues. First, check the fuel to ensure it's fresh and reaching the carburetor; old or contaminated fuel can cause starting problems. Additionally, inspect the air filter for clogs and the spark plug for wear or fouling, as both can hinder performance. Lastly, ensure that the carburetor is clean and functioning properly, as dirt or debris can affect fuel flow.
How do you rebuild Briggs and stratton ohv engine?
To rebuild a Briggs and Stratton OHV engine, start by disassembling the engine carefully, noting the order and orientation of parts. Clean all components and inspect them for wear or damage, replacing any faulty parts such as gaskets, rings, or valves. Reassemble the engine using a torque wrench to ensure proper tightness of bolts, and follow the manufacturer's specifications for reassembly. Finally, perform a thorough check of the fuel and lubrication systems before starting the engine to ensure it runs smoothly.
My Briggs and Stratton twin cylinder 16.5 hp engine backfires when it is turned of with the key and also backfires sometimes while running?
the seat on the exhaust valve is dirty so the valve does not seal it.... not sure how to clean it
