0
You have to pull the transmission out to get into the cylinder. Jeep sells them for 240. but carquest sells em for just over a 100. Im putting a clutch at the same time and mines at 86000 miles. Probably not necessary to do the clutch but since its a 5.5 hour job in a shop might as well have it done too. 130. for the clutch disk and pressure plate . 500 for labor and doing the u joints at the same time since they need to come out to do it.
What else can I help you with?
Do you have to pull motor to change the clutch slave cylinder?
Yes
How do you change Astra clutch slave cylinder?
To change the Astra clutch slave cylinder, first, ensure the vehicle is securely lifted and supported. Begin by draining the hydraulic fluid from the clutch system and disconnecting the hydraulic line from the slave cylinder. Remove any mounting bolts securing the slave cylinder to the transmission, then take out the old cylinder. Install the new slave cylinder, reconnect the hydraulic line, and refill the clutch fluid, ensuring to bleed the system to remove any air before testing the clutch operation.
How do you change a clutch slave cylinder on a 1988 Chevy S10 Pickup?
You will need to remove the transmission to replace the clutch slave.
How do you change the clutch slave cylinder in a 93 Ranger?
very carefully
How do you change out a clutch slave cylinder on a 1992 jeep cherokee laredo straight 6 cylinder 5 speed?
To change the clutch slave cylinder on a 1992 Jeep Cherokee Laredo with a straight 6 and 5-speed transmission, first, safely lift and support the vehicle. Remove the transmission access cover and disconnect the clutch line from the slave cylinder, followed by unbolting the slave cylinder from the transmission bell housing. Install the new slave cylinder, reconnect the clutch line, and bleed the system to remove any air. Finally, reassemble the access cover and check for proper clutch operation.
What if your clutch on your 85 Toyota corolla goes to the floor and is hard to shift?
There are two normal causes. The clutch is worn out or there is a leak in the hydraulic clutch slave or master cylinder. To check the clutch, press the clutch slave cylinder down. If the clutch slave cylinder bellows compresses down to the slave cylinder, the clutch is worn out. Check the clutch master cylinder fluid level. if this is low, then the clutch cylinder need to be checked. To check for a hydraulic leak in the clutch slave cylinder, remove the cylinder's bellows and check for any fluid. If fluid is present, rebuild or replace the cylinder and bleed the system. To check the clutch master cylinder, check the back the of clutch master cylinder for leaks. If fluid is present, replace or rebuild clutch master cylinder and bleed the system. In my experience, hydraulic leaks occur at the clutch slave cylinder.
Where is the clutch slave cylinder on a 1997 ford ranger?
The clutch slave cylinder for a hydraulic clutch is inside the manual transmission bellhousing
Where is the clutch slave cylinder on a 1994 pickup truck?
The clutch slave cylinder , for a hydraulic clutch , is inside the manual transmission bellhousing
What does the master and slave cylinder do for the clutch?
The master clutch cylinder is attached to the clutch pedal. When one depresses the pedal hydraulic fluid is forced from the master cylinder through the hard line to the slave cylinder. The piston in the slave cylinder is driven against the clutch linkage thereby releasing the clutch.
What type of fluid does the clutch slave cylinder use in a 1998 Mitsubishi mirage?
The clutch slave cylinder in your 1998 Mitsubishi does not use fluid. The clutch slave cylinder is sealed with grease inside of it.
Where is the slave cylinder?
It depends on the slave cylinder that you are asking about. The slave cylinder for a hydralic clutch would be neer the bell housing to disengage the clutch. The slave cylinder for drum brakes would be inside the drum between the two shoes, and pressure applied into this cylinder would engage the brakes.AnswerThe clutch slave is inside the bell housing on most of these. You have to pull the transmission etc to change it out. ANSWERSTRANSMISSION HOUSING OUTSIDE FLUID PIPE
Where is the bleeder on the clutch slave cylinder?
In cylinder
