0
From under the front vehicle on jackstands.....The bottom wheel of the u belt combo connecting the motor to the ac compressor, is "the" ac compressor that well has a bolt in the center of it. You must first remove the front skid plate (if equipped) from underneath the radiator and front of engine. It is easy, only 4 bolts. You will see a long tightening bolt along side of ac compressor. Loosen this "without" fully removing the nearly 4 inch long bolt. Now access the center bolt on the ac compressor wheel that the belt runs along. Loosening this bolt allows the the belt wheel to slide up and remove the old belt... if it is still on. Frequently with this piece of junk vehicle you will simply be putting a new one on. With the wheel loosened, reattach new belt so that the belt slides completely into the groove of both motor wheel and ac wheel. While pulling down on ac wheel, tighten the center bolt on it. Now re-tighten the long adjuster bolt "not too tight, it will break". If belt squeeks when you start car and ac, then slightly tighten the long one a little more. Replace skid plate. Done.
What else can I help you with?
How do you change out ac belt for 2001 Tahoe?
The ac belt has a tensioner that is accessed from below, and takes a tensioner tool to loosen. Remove the serpentine belt, release tension on the ac belt then the belt can come off for replacement.
How do you change a serpentine belt on a 98 Dakota 4x4 with AC?
buy a belt, loosen the tensioner, replace belt
How do you change a ac belt on a 2000 mirage?
To change the AC belt on a 2000 Mitsubishi Mirage, first, ensure the engine is off and cool. Locate the AC belt tensioner and loosen it using a wrench to relieve tension on the belt. Remove the old belt, then install the new one by routing it according to the belt diagram, usually found under the hood. Finally, retighten the tensioner and check the belt alignment before starting the engine.
Change the ac belt on frontier?
Release pressure on the tensioner. Remove the belt, paying attention as to how the belt is routed. Slide the new belt on using the same routing.
How do you replace the serpentine belt in a 1986 Pontiac fiero 2m6 se?
The "serpentine" belt does not serpentine. It runs the alternator and water pump only. To change you will need to work from underneath. If you have AC remove the AC belt by loosing the AC adjuster bolt and sliding the compressor over. If you have to take the AC belt off better change it, they are cheap and you don't want to do this again for a long time. Loosen the alternator adjuster pinch bolt. Some Fireos has a adjuster screw, some don't Move the alternator to loosen belt. Remove and install new. Tension belt to recommended tension on packaging on new belt. Reinstall AC belt, use the tension instructions on the package.
How do you change the AC belt on a 2003 suzuki swift 4x4?
To change the AC belt on a 2003 Suzuki Swift 4x4, first, disconnect the negative battery terminal for safety. Then, locate the AC compressor and loosen the tensioner pulley using a wrench to relieve tension on the belt. Remove the old belt from the pulleys and install the new belt, ensuring it follows the correct routing diagram. Finally, re-tighten the tensioner and reconnect the battery.
How do you change the AC belt on a 2003 infinity G35?
To change the AC belt on a 2003 Infiniti G35, first, disconnect the negative battery terminal for safety. Then, locate the AC compressor and use a wrench to relieve tension on the serpentine belt tensioner, allowing you to remove the old belt. Install the new belt by routing it according to the belt diagram usually found on a sticker in the engine bay, and then release the tensioner to secure the belt in place. Finally, reconnect the battery and check the installation by running the engine briefly.
How do you change AC belt in Chevy Avalanche?
If the belt only drives the ac compressor, loosen the compressor mounting bolts to let pressure off of the belt. Remove the belt and put on the new one. Pull the compressor to the side and put enough pressure to tension the belt as you tighten the bolts.
Cost to change an ac belt on a Nissan Murano?
You can't just change the a/c belt, its a serpentine belt, go to your shop, it should cost between $20-$50, I never needed one for my Murano yet.
How do you change ac belt on gmc Yukon?
Loosen the tensioner pulley. When the tensioner pulley is loose the belt will come off. Put the new belt on and tighten the tensioner pulley.
How do you Change AC belt 0n1995 geo prizm?
The AC comp should have a bolt(s) to loosen that will release tension & maybe addit'l idlers. Do that, slip off belt, put new 1 on, pry against the belt with a crowbar & tighten bolt.
How do you change AC belt on 2001 KIA Sportage?
Loosen the tensioner pulley. The tensioner pulley will make the belt loose. The belt can easily come off. Reverse the process to put on a new belt.
