0
How do you install a distributor assembly in a 92 Geo tracker 4 wheel drive automatic transmission?
start by taking the distibutor cap off, the bring the #1 cylinder up to tdc (top dead center) then see were the rotor is pionting. then remove the hold down plate & remove the distibutor. next drop the new distibutor in making sure you put the rotor-gear in the same place the old rotor was. tighten the plate bak down then start the car if the car does not start or it has a miss then turn the distibutor till the motor either starts or the miss is gone. then you will need to time it with a timing light, if you don't have one take it to a shop and they will tune it for you for less than nothing.
What else can I help you with?
Why does the transmission shifter lock how can it be fix?
install transmission shifter assembly
How do you change a 2 speed automatic car to a manual?
Buy a manual transmission that will bolt to your engine configuration, clutch assembly, drive shaft, et cetera. Install said parts and presto, you'll have a manual transmission car.
How do you convert automatic to manual transmission for 1992 Chevy beretta?
To convert a 1992 Chevy Beretta from automatic to manual transmission, you'll need to gather a compatible manual transmission, clutch assembly, pedals, and necessary linkage. Begin by removing the automatic transmission and associated components, then install the manual transmission along with the clutch pedal and master/slave cylinder. Modify or replace the wiring harness if needed, and ensure the driveshaft and mounts are compatible. Finally, fill the manual transmission with the appropriate fluid and test the system before driving.
How can you make manual 1988 suzuki alto auto transmission?
To convert a 1988 Suzuki Alto from automatic to manual transmission, you'll need to replace the automatic transmission with a compatible manual gearbox. This involves removing the automatic transmission, modifying or replacing the transmission mounts, and installing the manual transmission. You'll also need to change the clutch pedal assembly, install a clutch master and slave cylinder, and ensure the drive shaft is compatible. Finally, make appropriate adjustments to the wiring and any necessary components to accommodate the manual transmission system.
How do you change manual transmission into automatic?
This is a major mechanical project. Remove the clutch and manual transmission and the radiator. Install automatic transmission, new driveshaft, new radiator. You have just spent as much as a car is worth.
Can you install a 6 cylinder manual transmission in a 1996 Z28 Chevy Camaro?
you can install an automatic transmission, but i wouldn't try one from a v6 unless your motor is a v6 as well
How do you install a speed sensor on a DX 93 Honda civic with automatic transmission?
Take it to the dealer
1990 acura integra automatic transmission install I have a 1990 acura integra nad i need the steps to install a new automatic transmission into this car does anybody know how -donny?
Save up your money and have the job done by a pro, honestly, its a pain and not worth the savings.
How do you install 1993 rodeo distributor?
install distributor rodeo 1993
Can you convert a 02 suzuki liana manual to automatic?
Yes, you can convert a 2002 Suzuki Liana from manual to automatic, but it requires significant modifications. This process typically involves replacing the transmission, adding an automatic transmission control module, and possibly altering the wiring harness. Additionally, you may need to install a different pedal assembly and modify the driveshaft. It's a complex task best suited for experienced mechanics, and it may not be cost-effective compared to purchasing an automatic model.
How do you install a neutral safety switch on a 93 S10?
Standard or automatic transmission??? In most vehicle situations the switch unscrews out of the likage side of the transmission.
Where is the camshaft position sensor switch located on your 1995 Durango?
The Dodge Durango was introduced in 1998, so this question cannot be answered. However, in the 2000 Durango.... The camshaft position sensor is located in the distributor on all 3.9L V-6 and 5.2/5.9L V-8 engines Camshaft Position Sensor REMOVAL Distributor removal is not necessary to remove camshaft position sensor Remove air cleaner assembly. Disconnect negative cable from battery. Remove distributor cap from distributor (two screws) Disconnect camshaft position sensor wiring harness from main engine wiring harness. Remove distributor rotor from distributor shaft. Lift the camshaft position sensor assembly from the distributor housing Camshaft Position Sensor INSTALLATION Install camshaft position sensor to distributor. Align sensor into notch on distributor housing. Connect wiring harness. Install rotor. Install distributor cap. Tighten mounting screws. Install air cleaner assembly. (this info from post on answers.com about cps on 2000 durango)
