0
What else can I help you with?
What could be causing a rattling or knocking sound that happens after it warms up doesnt do it when cold and doesnt get worse as you accelerate on a Mazda 1986 b2000?
more than likely a valve!
What is the Valve clearance specs for a 1984 Mazda B2000 pickup?
Also,do you adjust them warm or cold?
Why does the heater blow cold air on a 1986 Mazda b2000?
A 1986 Mazda B2000 may blow cold air from the heater due to several potential issues. Common causes include a low coolant level, which can prevent the heater core from receiving enough hot coolant, or a malfunctioning thermostat that fails to open properly. Additionally, a clogged heater core or a faulty heater control valve could impede warm air flow. It's advisable to check these components to identify and resolve the problem.
What is the head torque on a 1983 Mazda B2000?
warm engine-95~100 Nm (69~72 ft lb) cold engine-82~88 Nm (59~64 ft lb)
How much horse power does a 2004 Mazda rx8 gain with an aem cold air intake?
idk exact specifics, but after installing mine there is a definite notice in increased hp. i strongly suggest the cold air intake.
What is the valve clearance for a 1986 Honda Fourtrax 125?
cold intake is 0.003 in or .07 mm cold exhaust is 0.003 in or .07 mm
How do you install cold air intake on Mazda Millenia?
To install a cold air intake on a Mazda Millenia, first, make sure the vehicle is turned off and parked on a flat surface. Begin by removing the factory air intake system, which typically involves loosening clamps and disconnecting any sensors. Next, follow the instructions provided with your cold air intake kit to assemble and position the new intake, ensuring all connections are secure. Finally, reattach any sensors and check for proper fit before starting the engine to test the new setup.
What is the tappet clearance for a 1986 Mazda B1600?
The tappet clearance for a 1986 Mazda B1600 typically measures 0.008 inches (0.20 mm) for the intake valves and 0.010 inches (0.25 mm) for the exhaust valves when the engine is cold. It's important to check the specifications in the owner's manual or service manual for precise measurements and procedures, as variations may exist. Regular adjustments can help maintain optimal engine performance.
What would cause my 1986 Mazda b2000 truck to make a tapping noise when it gets warm but not when it's cold?
Mazda had issues with poor oil circulation on the 1986-1990 models and some there after.Short of it is they did offer new valves with bigger oil ports to help fix the tap noise on cold start up.Now the 1986 model does require valve adjustments and the previous post recommended 15,000 miles which should be correct.But running 10w30 and changing the filter every 3000 helps alot.I would get the valves adjusted and do the normal service there after.Mazda has had this issue and even with my 87 it does it from time to time with the retro fit job done to it.Best suggestion and information I can offer after owning mine for 23 years.
How do you adjust the valve on 1990 B2000 pickup?
To adjust the valve on a 1990 Mazda B2000 pickup, first ensure the engine is cold. Remove the valve cover to access the rocker arms, then use a feeler gauge to measure the clearance between the rocker arm and the valve stem. Adjust the clearance by turning the adjusting nut on the rocker arm until the desired gap is achieved, typically around 0.008 inches for intake and 0.010 inches for exhaust valves. Reassemble the valve cover and ensure all components are securely fastened before starting the engine.
What are the valve settings for a 1986 Honda accord LX?
Valve clearance (cold) Intake 0.005 to 0.007 in Exhaust 0.010 to 0.012 in
How do you install a cold air intake on mustang?
By installing an cold air intake on a mustang
