answersLogoWhite

0

To replace the CV boot on a Vito van, start by lifting the vehicle and removing the wheel for access. Detach the axle from the wheel hub, then slide off the old CV boot clamp and boot. Clean the joint, apply fresh grease, and position the new CV boot onto the axle. Finally, secure the boot with new clamps, reattach the axle to the hub, and reinstall the wheel.

User Avatar

AnswerBot

1mo ago

What else can I help you with?

Related Questions

CV boot Ford Ranger how to replace?

A CV boot is found on the axle of a vehicle. To replace the outer boot remove the axle bolt and pull the boot off. The inner boot requires removal of the whole axle.


How do you replace a rear cv boot on a subaru wrx?

Lift the vehicle using a jack. Inspect the CV boot for problems. Mark the axle. Separate the CV from the shaft. Remove the CV boot clamps. Use a mallet to knock the CV joint off the shaft. Remove the boot from the CV axle shaft.


How do you replace the cv boot on a 1991 Nissan Stanza?

you cannot just change the boot you will have to replace the whole axle


How do you replace CV boot Integra?

To replace the CV boot on an Acura Integra, start by safely lifting the vehicle and removing the wheel. Disconnect the axle from the hub and slide it out of the transmission, then remove the old CV boot clamps and the boot itself. Clean the CV joint, apply new grease, and slide on the new boot. Finally, secure the new boot with clamps, reassemble the axle, and reinstall the wheel.


How do you change a CV boot on a Ford Escort?

It is cheaper to replace the CV shaft than it is to replace the boot. If the boot has been torn for any length of time it will have collected dirt and water. That in itself spells disaster.


How do you replace an CV boot on a 1998 Chevrolet Malibu?

It is much cheaper to replace the CV shaft. Purchase a Haynes manual that is specific to your car.


How much does it cost to replace Subaru Outback CV boot?

500


How do you fix a cv boot for a 1993 Ford Escort?

They make replacements that are split in half, but they aren't generally recommended. What's best (unfortunately) is to remove the shaft and replace it with a stock cv boot. If the cv boot has been open to the elements for a while, damage in the cv joint might have occured.


How do you replace the CV boot on a 2011 Nissan Rogue?

To replace the CV boot on a 2011 Nissan Rogue, start by safely lifting the vehicle and removing the wheel. Next, detach the axle from the hub and remove the old CV boot by cutting it off. Clean the CV joint and replace it with fresh grease, then slide the new boot onto the axle and secure it with clamps. Reassemble the axle into the hub, ensuring all components are properly aligned, and finally, reinstall the wheel.


How do you replace a cv boot on a 2002 Subaru Forester?

To replace a CV boot on a 2002 Subaru Forester, first, lift the vehicle and remove the wheel. Then, detach the axle from the hub and slide it out of the transmission. Remove the old CV boot clamps, clean the joint, and apply new grease before fitting the new boot. Finally, secure the boot with new clamps, reassemble the axle, and reinstall the wheel.


Can you re-grease the boot for a cv joint until you can get it replaced?

Yes, you can re-grease the boot of a CV joint as a temporary fix until you can replace it. Carefully clean the area to remove any dirt or old grease, then apply a suitable CV joint grease into the boot. Ensure the boot is properly sealed to prevent further contamination. However, this is a short-term solution, and you should replace the CV joint or boot as soon as possible to avoid potential damage.


How do i replace the cv boot on an 1987 GMC Jimmy?

Don't bother, just replace the entire axle. Once the boot is damaged, the CV joint is contaminated and it will not last very long. It's just an exercise in futility to replace the boot, and the effort is almost as great as if you replaced the entire half-shaft axle.