0
First, remove the inside trunk lid cover panel.
Disconnect the electrical connection.
Use a spin tight wrench (7mm) to remove the two screws.
Unclip and remove the protective cover.
Unclip and remove the light fixture.
The light fixture is LED so you will need to replace the entire fixture, it's about $60 at the dealership.
I just did this procedure last night.
What else can I help you with?
Why do the rear brake lights come on when you are driving your 2006 Chevy Malibu?
Bad brake light switch, it's on top of the brake pedal under the dash.
How do you replace third brake light on a 2006 Mitsubishi eclipse?
You have to remove the interior trim of the lift gate.
How do you replace the bulb in high mount brake light for a 2006 Hyundai Sonata?
you need to remove the rear seat
How do you reset the break wear light for a 2006 c230?
no reset needed,just replace the brake pads sensors
How do you replace a brake light on a 2006 Mazda 3 tail light to a led brake light?
To replace the brake light on a 2006 Mazda 3 with an LED brake light, first, open the trunk and remove the access panel or screws securing the tail light assembly. Disconnect the wiring harness from the bulb socket and remove the old bulb by twisting it counterclockwise. Insert the new LED brake light bulb into the socket, ensuring it fits securely, then reconnect the wiring harness and reassemble the tail light assembly. Finally, test the new LED brake light to ensure it's functioning properly.
How do I replace the Corolla 2006 brake light?
To replace the brake light on a 2006 Toyota Corolla, first, open the trunk and locate the tail light assembly. Remove the screws or clips holding the assembly in place, then gently pull it out. Twist the bulb socket counterclockwise to remove it, replace the old bulb with a new one, and reassemble by reversing the steps. Ensure the new bulb is securely in place before testing the brake lights.
How do you replace the 3rd brake light on a 2006 Cadillac dts?
To replace the 3rd brake light on a 2006 Cadillac DTS, first, open the trunk and remove the access panel located at the rear of the trunk, which may require unscrewing or unclipping. Next, disconnect the wiring harness from the brake light assembly and remove the screws or clips holding the assembly in place. Replace the old light with a new one, reassemble the components, and reconnect the wiring harness. Finally, test the new light to ensure it functions correctly.
How do you replace 2006 Lincoln ls brake lights?
I have a 2006 lincoln ls sport in which the 3rd brake light cover isn't connected properly. When I drive I can see out of my mirror that it's moving. Is there a way to keep it from moving?
How do you replace brake lights in brake bar of Cadillac 2006 dts?
To replace the brake lights in the brake bar of a 2006 Cadillac DTS, first, open the trunk and remove the access panel or cover on the side of the brake light assembly. Next, twist the bulb socket counterclockwise to remove it, then take out the old bulb and replace it with a new one. Reinsert the socket back into the assembly, ensuring it locks into place, and finally, replace the access panel. Test the brake lights to confirm they are functioning properly.
How do you reset brake light on 2006 BMW 525i?
how can i reset rear brake pad warning light on 2006 bmw 525i
How do you replace sending unit on a 2006 Chevy Malibu?
Need to know which sending unit you want to replace, there are several.
How do you change a 2006 Acura brake light?
To change the brake light on a 2006 Acura, first, open the trunk and locate the tail light assembly. Remove the screws or clips securing the assembly, then gently pull the assembly out from the vehicle. Disconnect the electrical connector and twist the brake light bulb counterclockwise to remove it. Replace it with a new bulb, reconnect everything, and reattach the assembly to finish the job.
