answersLogoWhite

0

First, you need to access the side panels from the trunk. There are two screws on each side. You will need to remove the jack holder to reach one of the screws. Then you will need to remove the rear light assemblies. Once you have pulled those off, you'll find a couple friction fittings underneath, pull those out. Just to the sides of the light, inside the trunk, there is a nut angle upward in the corner, kind of hard to spot if you're not looking for it. Remove one from each side. Then you only have a three screws around the outside of the bumper on each side, and two more friction fittings on the bottom rear of the bumper. Now the bumper should easily come off, just be careful to disconnect side parking lights as you remove the cover.

User Avatar

Wiki User

19y ago

What else can I help you with?

Related Questions

How do you replace the front bumper cover on a 2000 Intrepid?

To replace the front bumper cover on a 2000 Dodge Intrepid, start by disconnecting the battery and removing any screws or clips securing the bumper cover to the vehicle. Next, detach the fog light connectors and any other wiring attached to the bumper. Carefully pull the bumper cover away from the car, ensuring not to damage any clips. Finally, align the new bumper cover, reattach it with screws and clips, reconnect any wiring, and reconnect the battery.


How do you change the fog light bulb on a 2000 Maxima?

how do you replace a bulb in a fog light on a 2000 maxima?


How do you replace a front grille on a 2000 Windstar?

You can't - well, you can.. but the front bumper cover and the grill are all one piece


How do you replace the center vent cover on a 2000 Nissan Maxima SE?

Just pull it out by the two slots under the vent ajusters.


How do you replace a rear bumper cover on a 2000 Toyota Camry?

To replace the rear bumper cover on a 2000 Toyota Camry, first, remove any screws, clips, or fasteners securing the bumper to the vehicle, which are typically located in the wheel wells and under the rear of the car. Next, gently pull the bumper away from the body, disconnect any electrical connections for lights if applicable, and then remove the old bumper cover. Align the new bumper cover with the mounting points, reconnect any electrical components, and secure it with the screws and clips you removed earlier. Finally, ensure everything is tightly fastened and check for proper fit.


Where is the alternator and how do you replace it on a Nissan Maxima?

what year maxima? 1989-1994 on the bottom.. 1995-2000 in the middle..


How do you remove rear bumper cover for a 2000 Buick Lesabre?

,


Can you use a 1999 infiniti g20 rear bumper cover on a 2000 infiniti g20?

Yes. The rear bumper cover was the same on the Infiniti G20 from 1999-2002.


What is cost of replacing starter motor on 2000 Nissan Maxima SE?

I have recently replace my starte for 2000 nissamn maxima gle and it cots around 500 usd with parts and labor.


How do you replace the License plate bulb on a 2000 Chevy blazer?

Lift up slightly, then rotate the black plastic cover and it will loosen and pull out of the socket in the bumper. Once it is removed from the bumper, grasp the rear of the wiring harness and twist to expose the light bulb. Replace the bulb, then reassemble in the reverse order.


2000 Nissan Maxima - Does anyone know where the PVC valve is located on this engine and how to change it out?

The PVC valve on a 2000 Maxima is located in the rear valve cover just behind the throttle body. REMOVAL # Grasp the PVC valve and pull it out of the valve cover


How do you remove the headlamps on a 2000 Volkswagen Jetta?

REMOVE TWO TOP BOLTS ON HEADLAMP ASSY. THEN REMOVE BUMPER COVER, THATS RIGHT THE BUMPER COVER, THEN REMOVE TWO BOTTOM BOLTS