answersLogoWhite

0

The horsepower gain from a 650 Edelbrock carburetor on a 302 motor can vary based on several factors, including the engine's overall setup and tuning. Typically, a properly tuned 650 cfm carburetor can help a 302 motor produce anywhere from 20 to 50 additional horsepower compared to a stock carburetor. However, for optimal performance, it's crucial to ensure that other components, such as the intake manifold and exhaust system, are also upgraded accordingly.

User Avatar

AnswerBot

6d ago

What else can I help you with?

Related Questions

Where would you find a vacuum line routing diagram for a small block 350 with a 600 cfm edelbrock carb on it?

go to google or yahoo and do a search for "vacuum line routing edelbrock"..... it should give you alot of pages. choose the one from edelbrock.


How do you calculate horse power of water pump?

You can approximate the horsepower capabilities of any electric motor by calculating incoming electric power. This is done by simply multiplying the rated voltage by the rated current. This will give you a unit of watts. There are about 746 watts per horsepower. Say if the motor is about 85% efficient, then incoming power will match output power minus this efficiency. Anyways, multiply incoming power by .85 and divide by 746 should give an approximate horsepower of the water pump's motor.


What is the service factor of motor?

service factor of motor is 1.00 or 1.15 . almost all electric motors rated at 1.5 horsepower or more have a service factor of 1.15 or greater. a motor with a 1.00 service factor is usually a very small motor like an exhaust fan in residential bathroom. if a motor has 1.00 service factor all that means is that it can only operate at 100% of its rated amperage. a motor with a 1.15 service factor can periodically be run at 115% of its rated amperage without damaging the motor.


Minimum breaker size 60 horsepower motor?

A 60 horsepower motor typically requires a minimum breaker size of 100 Amps for normal operation. It is important to consult the motor's specifications or a licensed electrician to ensure the correct breaker size for safe and efficient operation.


How do you get a carburetor on LEGO?

Give a tire to Radia Give a tire to Radia


What motor is on a hustler super z serial?

The Hustler Super Zs typically have Kawasaki motors. The actual engine size and horsepower vary depending on the model. I would need more information to give you the exact motor.


How do you convert LRA to Horsepower?

LRA is not any known unit of measure. You can convert horsepower to BTU per hour, calories per second, ergs per second, watts, Kilowatts, MW, GW, etc.


Difference between horsepower and torque?

Torque is the measurement of turning force. A wrench applies torque to a bolt. A motor or engine provides torque to do work. Horsepower is the measurement of the work done or ability to do work. This is done by taking the speed the engine is operating at (RPM) and what torque it is producing and applying a formula to give a horsepower rating.


What kind of edelbrock carburertor 600 or 750 cfm should i use with 350 Chevy engine with 350 horse power?

The 600 should give better throttle response, whereas the 750 should produce more horsepower above 5000 rpm. Most people are more satisfied with the smaller carb in these situations.


Can anyone estimate how much horsepower torque these parts on a 350 Chevy can give 1-600cfm holley manual choke vacuum secondaries 2-edelbrock torker 2 intake single plane?

Impossible to estimate without detailed information about compression ratio, cam profile, and cylinder head configuration. In general, adding a single plane intake to a stock engine will significantly reduce low-end torque. The Edelbrock Torker II is the worst single plane intake I have ever had the misfortune of using.


Where does the fuel line go on the carburetor?

It goes on the fuel inlet of the carb. Without knowing the exact carburetor you are referring to that is really the only answer I can give.


Does dropping your car give you more horsepower?

No