answersLogoWhite

0

the crankshaft position sensor is located right behind the harmonic balancer mounted on the timing cover

User Avatar

Wiki User

16y ago

What else can I help you with?

Related Questions

How do you install a CrankShaft Sensor in a 95 Buick Century?

Pull the front cover off of it, Behind the Crankshaft balancer, The sensor is there. a diagram of how to install a creckshaft sensor.


1997 BUick LeSabre Custom location of crankshaft sensor?

the crankshaft sensor is located behind the harmonic balancer on the ft timing cover


How do you install a crankshaft sensor on a 1992 Buick Century?

take off your harmonic balancer the answer is behind


Where is the crankshaft sensor on 2001 Buick Century?

its right behind the harmonic balancer....so you will have to remove the h.b them remove the crank sensor...


Where is a Buick crankshaft position sensor?

The crankshaft position sensor on a Buick is located behind th Harmic balancer. It should have a wire plugged in to it.


How do you remove a Crankshaft Position Sensor?

how to remove crankshaft position sensor from 91 Buick Regal


Airbag sensor location 2002 buick century?

under pass seat


Where is the crankshaft position sensor located on a 95 buick century?

behind the power steering pump on the passenger side of the engine


Where is the cam sensor location on a 1997 Buick Le Sabre?

On front cover of engine, slightly above crankshaft pulley.


Where is the crankshaft position sensor located on a 92 Buick Regal 3.1 V6?

The crankshaft position sensor, on your 1992 Buick regal 3.1 liter, is located on the back of the engine. The crankshaft position sensor is on the inside of the engine cover.


How do you take out crankshaft on 2001 Buick Century?

How to take out crank shaft on century 2001 buick century


Location of crankshaft sensor on 95 Buick Roadmaster?

The crankshaft sensor on a 1995 Buick Roadmaster is typically located near the bottom of the engine, behind the harmonic balancer or crankshaft pulley. It is usually mounted on the engine block or the timing cover, close to where the crankshaft is located. To access and replace the crankshaft sensor, you may need to remove other components such as the harmonic balancer, belts, or other engine parts for better visibility and access.

Trending Questions
What size wiper blades fit a 2011 Lancer? Why won't my driver seat move up all the way? How many quarts does a 208 transfer case hold? Is there parking bypass codes for Clarion Vx300? Where is the Location of fuel filter for 1995 GMC Sierra? How can you remove oil pan on 95 Lincoln tc? What coolant do I use for 2011 Volvo xc60? Can you replace just the battery on the key fob? How do you replace the rubber strip on the roof of a 2000 Honda civic it runs from the front windshield to the rear windshield there is one on each side of the roof? Why does the battery not stay chargedbattery and alternator test good wires leading to th alternator are clean looking and the only lights that come on are the check gauges light when the battery dies? Why would transmission fluid go in the air intake? How do you replace the fuel filter on a 2006 envoy? How do you remove the front rotors on a 1997 Ford F-350 auto trans four wheel drive? What is the size of catalytic converter for Suzuki Vitara jlx 1994 model? Your 98 Jeep Wrangler Makes clicking noise while driving even worse when clutch is engaged Sound is either coming from clutch or transmission. Please help shed some light on this problem? Montero Sport makes loud squeaking noise around compressor and will not blow cold air? 2003 S10 temperature sensor location? How many quarts of oil are in 2009 vw rabbit 2.5liter? What is draining new battery and alternator on BMW 525i? What is the ratio of air fuel mixture in diesel cycle?