0
What else can I help you with?
Where is the clutch hose on a 1989 Honda Prelude?
On a 1989 Honda Prelude, the clutch hose is typically located between the clutch master cylinder and the clutch slave cylinder. The master cylinder is mounted on the firewall in the engine bay, while the slave cylinder is located on the transmission. The hose runs along the chassis, connecting these two components to facilitate hydraulic fluid transfer for clutch operation. Always refer to a service manual for precise locations and diagrams.
Where is the clutch fluid in 1992 BMW 318is?
it is in the master brake bottle the clutch feeds threw the hose at the drivers rear of the brake bottle
Why would clutch fluid leak out on a 88 Toyota corolla?
Bad clutch slave cylinder or failed soft hose from master to slave cylinder.
Picture of clutch cable on 1990 Mazda 323?
there is no clutch cable. it has a hydraulic clutch. there will be a clutch master cylinder on the firewall near the brake M/C. a hydraulic hose will connect that to the clutch slave cylinder on or near the tranny. the slave cylinder pushes on a fork (lever) that disengages the clutch.
Where does the clutch fluied go on a 74 vw bug?
Unless someone has done a custom hydraulic clutch setup on this vehicle- there is no clutch fluid. It is a cable clutch linkage on a stock vehicle. If it has been customized there will be a easily identifiable reservoir connected to the clutch pedal or connected to the clutch master cylinder by a hose.
Where is the clutch fluid reservoir in a 84 vanagon?
From what I've read about changing the clutch master cylinder the resivor is behind the instrument cluster (spedo) ;) you can follow the hose from the master cylinder above the clutch pedal.
How do you remove the clutch cable end from a 1997 Chevy MG5 5 speed tranny?
disconnect the hose from the clutch master cylinder on the firewall. I has a little retaining pin in it use a nail or something small to push it out then you can drop the tranny with a 4 foot line connected to it once you see the slave cylinder you can disconnect the hose the same way the hose was connected to the clutch master cylinder I learned this when I had to replance my slave cylinder
1996 1500 6 cylinder 5 speed pick up has new clutch no pressure on clutch pedal no leaks around master cylinder will not go in gear where do you look next?
did u bleed all the air out of the system on slave there is a bleeder run hose from that to fluid in master make Sher hose is sealed open bleeder keep end of hose in hydro fluid and pump clutch until no air comes from hose 2 person job close bleeder
Where do you put clutch fluid in 92 ford esort lx?
your clutch run's of off your brake fluid the place where you put your brake fluid in to fill it up there is a hose the run's from it. it goes to your clutch master cylinder
Why does the clutch pedal stick to the floor?
You've blown a clutch hose by the sound of it, or you've got a leak in the clutch master or slave cylinder. Either way, without clutch fluid, the clutch pedal wont come off the floor and the clutch will be disengaged. Any half decent mechanic should be able to figure out what the issue is without charging and arm and a leg.
How do you fit a vauxhall vectra clutch MASTER cylinder AND how do you determine if its knackered?
Remove the clevis pin from the pedal the remove the master cyl from the bulkhead A quick way to test the cylinder is clamp the flexible hose that leads to the slave cylinder when the hose is clamped, the clutch pedal should be solid.
How do you bleed the clutch on a 2000 Toyota Tacoma 4x4?
the best way to "bleed" any clutch is to get a can with a pump and a hose that will fit over the bleed screw. Loosen the bleed screw put the hose over it and pump fluid back up to the master cylinder this will force any air out.
