0
What is a drive cycle and how many times it needs to be run to reset test sensors on most cars?
# Cold Start the engine. For Cold Star, the engine coolant temperature must be below 50°C (122°F) and within 6°C (11°F) of the ambient air temperature at startup.
# Idle the engine in drive for two and a half minutes with the A/C and rear defroster on.
# Turn the A/C and rear defrost off, and accelerate to 55 mph (88km/hr) at half throttle.
# Hold at a steady speed of 55 mph (88km/hr) for three minutes.
# Decelerate (coast down) to 20 mph (32km/hr) without braking or depressing the clutch.
# Accelerate back to 55 to 60 mph (88-96) km/hr at ¾ throttle.
# Hold at a steady speed of 55 to 60 mph (88km/hr) for five minutes.
# Decelerate (coast down) to a stop without braking.
For more info look at the related link below.
What else can I help you with?
What is the Drive cycle 2003 olds alero to reset sensors?
Dan T
How do you reset the obdii drive cycle on 2003 Mercedes Benz e500?
How do you reset a e500 mercedes benz drive cycle
What is the drive cycle to reset 2001 Toyota solara?
what is the drive cycle of Toyota solara 2002
How do you reset the drive cycle on the obdii Honda crv 2002?
To reset the drive cycle on a 2002 Honda CR-V, you typically need to clear the vehicle's diagnostic trouble codes (DTCs) using an OBD-II scanner. After clearing the codes, the drive cycle can be completed by following a specific sequence of driving conditions, which usually includes a mix of idling, acceleration, and steady-speed driving. This allows the onboard systems to recheck and recalibrate various sensors. Make sure to drive the vehicle under varied conditions to ensure all readiness monitors are reset.
How far do you have to drive after having the check engine light reset?
After having the check engine light reset, you generally need to drive the vehicle for about 50 to 100 miles to allow the onboard diagnostic system to run various tests and recheck the vehicle's systems. This drive cycle typically includes a mix of city and highway driving to ensure all sensors and components are evaluated. If the light comes back on, it indicates that there is still an issue that needs to be addressed.
Do you have to operate the sienna after battery replacement to reset the computer?
to reset the old codes you must drive it for atleast an entire drive cycle
How do you reset the drive cycle on the computer of a Honda element?
You take out the battery and reinsert it.
How do you reset all sensors in a 2001 S430?
What sensors??? Tire pressure sensors? You can reset the tire pressure sensors through the instrument cluster
How do you reset the drive cycle on the OBDII computer on a 2004 mercury monterey?
To reset the drive cycle on the OBDII computer of a 2004 Mercury Monterey, you can disconnect the vehicle's battery for about 10-15 minutes, which clears any stored trouble codes and memory. After reconnecting the battery, you will need to drive the vehicle through specific driving conditions to complete the drive cycle, including a mix of stop-and-go and highway driving. Make sure to follow the manufacturer's recommended drive cycle procedure to ensure all readiness monitors are reset.
What is the drive cycle for a 1998 dodge stratus?
I have a 1998 dodge stratus and the obd inspection results are showing notcomplete or unsupported. I have been told to drive the car so the computer can reset. What is the drive cycle for this car. I have a 1998 dodge stratus and the obd inspection results are showing notcomplete or unsupported. I have been told to drive the car so the computer can reset. What is the drive cycle for this car.
How do you reset the obd2 drive cycle for 1999 s-10 Chevy?
Disconnect the battery.
How do you reset the CPU on a 1998 Safari?
There are 2 possible ways to reset the computer, 1. if it doesnt have a "hard" code in it then you can just disconnect the battery wait for 5mins then reconnect the battery. 2. have a repair shop put the OBD tester on it extract the codes (hopefully fix any codes there) then clear the codes this will reset the computer it will take a completed drive cycle to see if the problem returns. In both cases normal driving will take a couple of days to do the drive cycle and to get all the sensors back online.
