0
What is cross reference number for Briggs and stratton fuel bowl gasket part 281165s to stens number?
STENS 485-076 BOWL GASKETabout 98% sure
What else can I help you with?
What is head gasket torque setting on 17.5 hp Briggs and stratton?
220 in-lbs
How do you fix a blown head gasket in a Briggs and Stratton lawn mower?
Take all the shrouds off remove the head bolt remove the head gasket clean off the dirt then reverse the process. Hope this helps
Riding mower Briggs and stratton blowing out oil?
The most common place for oil leaks is the sump/crankcase cover gasket. A torn gasket will allow oil to escape. A common cause could be a blown head gasket putting too much pressure in the crankcase.
You have a 12.5 Briggs stratton engine the bolts in the lower case came loose you are replacing the gasket but need to know if there is an alignment on the gear to the govenor?
No alignment is necessary on governor gear, only the camshaft (timing) gear.
Why won't fuel primer work on briggs and stratton lawn mower engine?
Check the gasket between the air filter backing plate and the carburetor. Usually if that is sucking air then the primer won't work. Your best bet would be to just replace the gasket and possibly the primer bulb as well
What if your 3.75 hp Briggs and Stratton lawn mower runs rough like it is about to cut off when the tank is full of gas but runs fine when the tank is almost empty how can you correct this problem?
Change the gasket under the carb. The part cost about $5 and will take you about 30 minutes to change.
Why Briggs and stratton Front Tine Tillers leaks fuel?
Briggs and Stratton Front Tine Tillers may leak fuel due to several reasons, including a damaged or worn fuel line, a faulty fuel shut-off valve, or a defective carburetor gasket. Additionally, loose connections or a cracked fuel tank can also contribute to leaks. Regular maintenance, including checking for cracks and ensuring all connections are tight, can help prevent fuel leaks. If the problem persists, it's advisable to consult a professional for repairs.
Why does your Briggs and Stratton emit white Smoke and burn oil?
White smoke is eaither a blown head gasket or you have water in the fuel system. This is not to be confused with flooding an engine and seeing white vapor coming out of the exaust in which that would NOT be smoke, it would be gas vapor's. If your burning oil, the smoke will be blue and smells of burnt oil.
Why is your 4 cycle engine blowing oil through the air cleaner?
Well first of all, what size or brand of engine? If it is a lawn mower engine, it deals with incorrect crankcase pressure from most likely a head gasket failure and/or breather problem. Briggs & Stratton engines thru the 90's are very known for this on the rider mower engine.
How do you select the thickness of replacement crankcase gasket Briggs model 281707 Craftsman mower?
put the crankcase together with no gasket and move the crankshaft. the amount of movement you get will determine the gasket thickness. if it is a lot of play then use the thick gasket, if there is little to no play use the thinner one and if the movement is in between use the middle thickness gasket. not a super technical answer but it should help you out
What causes 16.5 Briggs and Stratton backfire a lot while in use?
There are several reasons the engine would backfire, but the three main culprits are a dirty air filter, a loose intake manifold bolt or gasket (vacuum leak), or a faulty spark plug. If the problem is not one of these three, check out a book on small engine trouble-shooting and repairs from your local library. You will find other procedures a little more complicated in the manual to help you trouble-shoot.
How do you install a Briggs and Stratton 6 hp camshaft?
You must first split the case after draining the oil of course then pull the cam out being careful of your lifters not to fall out if they do just put them back in . . . now when you go to put the new cam in there is a dot on the camshaft and the crankshaft that has to be lined up in order for you engine to be in time. Make sure to line those up when you put the new cam in and you will most likely have to replace the crankcase gasket before putting it back together unless you managed not to rip the gasket when you split the case. After you put it back together put oil back in it normally around 1 quart and then you are good to go.
