0
wish i can tell u but ur best bet is calling dealership directly or sometimes a part store will have it in the computer and yes dealership will usally try to get you to come in but be persisent that you will or can not and just want but off the top of my head i believe its 15 to 17 pounds of torque for the pinion nut srry couldn't be more helpful
What else can I help you with?
What is the rear differential pinion nut torque specs?
What is the torque specs on a 2001 ford truck rear end pinion nut..
What are the torque specs for the pinion nut on a GM 8.5 3.42 rear end?
The General Motors 3.42 rear end pinion?ænut torque specification is 240 pounds. The pinion nut should be torqued in 80 pound intervals.
What is the rear differential pinion nut torque spec Toyota 8 inch?
I don't believe there is a specific torque specification! Once you install the crush sleeve and tighten the nut to the desired preload on your pinion bearings, your torque will be what it will be.
Changing rear differential pinion seal on 2003 dodge quad cab 1500 and the torque specs for pinion nut?
210ft. lbs.
84 gmc vandura how to replace rear axle pinion bearing?
To replace the rear axle pinion bearing on an '84 GMC Vandura, first, safely lift and support the vehicle, then remove the driveshaft and any rear axle cover. Next, remove the pinion nut and yoke to access the pinion gear. Carefully pull out the pinion assembly, replace the old bearing with a new one, and reassemble by reversing the steps, ensuring proper torque on the pinion nut and checking the bearing preload. Always consult a repair manual for specific torque specifications and procedures.
What is the rear pinion torque spec for 1994 S10 4wd?
The rear pinion torque specification for a 1994 Chevrolet S10 4WD typically ranges from 20 to 30 foot-pounds. It's important to consult the vehicle's service manual for the exact specification, as variations can occur based on the specific rear axle type. Always ensure that the pinion nut is properly torqued to avoid issues with the differential.
What is the torque for the pinion nut on a 68 firebird 10 bolt rear end?
The torque specification for the pinion nut on a 1968 Firebird with a 10-bolt rear end is typically around 30-35 ft-lbs. It's important to ensure that the pinion bearing preload is set correctly, which may require additional adjustments after achieving the initial torque. Always refer to a service manual for the specific vehicle for the most accurate information.
What is the rear differential pinion nut torque specson a ford 9 inch?
The rear differential pinion nut torque specification for a Ford 9-inch rear end typically ranges from 200 to 250 ft-lbs, depending on the specific application and whether a crush sleeve is used. It's important to ensure that the pinion preload is set correctly during installation, which may involve adjusting the torque to achieve the desired bearing preload. Always refer to the specific service manual for your vehicle for the most accurate specifications.
I have a 2001 dodge neon. I am replacing the rear hub assembly. does anyone know the rear wheel bearing torque?
The rear wheel torque spec for a 2001 Dodge Neon is 160 foot pounds.
What is 1995 Ford pick up with traction lock rear pinion nut torque?
The only torque you should be concerned with is the torque it takes to rotate the pinion gear alone, 8-14 inch pounds for old bearings, 16-29 in/lbs. for new bearings. The torque it takes to crush the crush collar (tightening the pinion nut) will be above 140 foot lbs. and this will set your tension on the pinion bearings. If you put a new crush collar in you are going to have to remove axles and carrier to get the proper pre-load on the pinion bearings.
How do you change rear differential pinion seal on 2003 Dodge quad cab 1500 and the torque specs for pinion nut?
just got my 2004 ram done at the dealer for 83 bucks. worth the money and have them do it :)
2001 Chevy blazer pinion seal replaced and noise heard now?
It sounds like the pinion nut is not tight enough and the pinion is now moving in and out. This will do bad damage to ring and pinion. You will need to replace crush sleeve in rear end now.
