0
What tool is needed to remove bolt for crankshaft position sensor OR what size is the bolt on 2001 KIA Sportage?
best to read up on it..
everyone should have a manual for their vehicle, and the library should have a professional manual available...in the reference section, you'll have to make copies of the important sections...good luck :)
It takes a ten millimeter to remove that bolt and it is hard to get to
What else can I help you with?
How do you remove a Crankshaft Position Sensor?
how to remove crankshaft position sensor from 91 Buick Regal
Where is the crankshaft position sensor in a 2002 Kia Sportage?
In a 2002 Kia Sportage, the crankshaft position sensor is typically located on the engine block, near the crankshaft. It is often found near the bottom of the engine, close to the oil pan or timing cover. To access it, you may need to remove some components, such as the air intake or other parts obstructing the sensor. Always consult the vehicle's service manual for the exact location and any specific removal instructions.
How do you remove a crankshaft position sensor gear?
Press off the balancer .
Where is the crankshaft position sensor on a 2001 Chevy Tahoe with a 5.3?
The crankshaft position sensor is located right above the starter, you may have to remove the starter for better visibility.
Where is the crankshaft sensor located on a Mazda B2500?
Hello! The crankshaft position sensor is located behind the crankshaft pulley,on the left side facing the front of the car.It is difficult to see and to remove it you need to remove the crankshaft pulley ( radiator,belts,.... )
Where is the crank shaft sensor on 01 Kia Sportage located?
The crankshaft position sensor on a 2001 Kia Sportage is typically located near the bottom of the engine, close to the crankshaft pulley. It is usually mounted on the engine block or transmission bell housing. To access it, you may need to remove any necessary components obstructing its location, such as the intake manifold or engine covers. Always refer to a service manual for specific details and diagrams.
What size wrench is needed to remove oil drainplug for 2000 kia sportage?
19 mm
How do you remove a crankshaft position sensor on a 1997 Infiniti QX4?
To remove the crankshaft position sensor on a 1997 Infiniti QX4, first, disconnect the negative battery terminal to prevent electrical issues. Locate the sensor, which is typically situated near the crankshaft or engine block, and unplug the electrical connector. Then, remove the mounting bolt(s) securing the sensor and carefully pull it out from its housing. Finally, inspect the O-ring for wear before installing a new sensor, if needed.
Where is the crankshaft position sensor located on a 1998 Mitsubishi Eclipse?
Crank position sensor is located next to the crankshaft. In order to replace it you might have to remove the timing belt. In the most models you just can remove remove the timing belt cover and replace the sensor.
Where is the crankshaft posion sensor in a 92 civic?
Remove the engine brush cover under the front of the engine. Remove the drive belt to make changing the sensor easier (optional). Remove the lower timing belt cover and the crankshaft pulley to access the crankshaft position sensor. Disconnect the electrical modules from the crankshaft position sensor, located next to the alternator. Take off the bolts with a socket wrench and remove the sensor.
Where is the crank position sensor for 1997 Chevy Malibu?
The 1997 Chevy Malibu crankshaft position sensor can be found on the back of the engine. You will need to remove the rear engine cover in order to access the crankshaft position sensor.
Where is the crankshaft position sensor and the camshaft position sensor located on a 2000 omega?
opel omega crankshaft sensor is located next tp the oil filter atached with a star shaped screw, to remove it you have to remove the oil filter first. or the muffler.
