0
Where is the grease jerk for the throw out bearing on a 91 s 10 2 point 5 you have to slightly put your foot on the clutch to get it to stop squeaking?
Throwout bearings are permanently lubricated and as such do not have a grease fitting. If the bearing grinds when you press the clutch your throwout bearing is trashed. Since it only makes noise when your clutch is rattling around, it's just an annoyance. If it gets to the point where it makes noise when you press the clutch you need a clutch job.
What else can I help you with?
Is there a difference between suspension grease and bearing grease?
There is a difference in the two. Suspension grease will be thinner and the bearing grease would be much thicker in density .
What are the symptoms of a bad clutch in a 2003 Chevy cavalier?
If its slipping you will smell it. If it shutters you probably have grease spots on your fly wheel. Grinding noise may mean you need a new pilot bearing(throughout bearing).
Why is there an inch between the throw out bearing and clutch and wont go in gear after replacing clutch on a 2004 mustang?
I'm going to bet that you didn't line up the plate with a dummy shaft and the pilot shaft is hitting the pilot bearing. That would keep the bell housing from bolting up to the engine and give you about an inch of gap. If you used the old trick of popping the pilot bearing with grease and a drift, and you left the grease in the pilot bearing hole, that would prevent the pilot shaft from seating deep enough.
How to fill grease to self aligning bearing?
To fill grease in a self-aligning bearing, first ensure the bearing is clean and free from old grease. Use a grease gun to inject the appropriate type of grease into the bearing housing through the designated grease fitting or port. Fill until you see grease emerging from the bearing seals, indicating it is adequately saturated. Finally, wipe away any excess grease to prevent contamination and ensure proper operation.
What causes clutch chatter?
grease or oil on the clutch facing
Can you grease a sealed bearing without damaging it?
No, you should not grease a sealed bearing as it can damage the seal and compromise its effectiveness.
How much grease should be applied to a bearing?
The amount of grease to apply to a bearing depends on the size and type of bearing. Generally, a thin layer of grease is sufficient to lubricate the bearing effectively. Over-greasing can cause overheating and damage to the bearing. It is recommended to refer to the manufacturer's guidelines for the specific bearing being used.
Why is my Car making squeeking noise when you depress the clutch?
The clutch pedal pivots on a rod (under dash connected to pedal). There are plastic bushings that it moves against, they may be worn or need to be greased (wheel bearing grease works). Make sure you assemble parts (after coating grease) the EXACT opposite way you disassembled them.
How do you pack a wheel bearing?
If you uave a can of grease,you can put the bearing down in that and work it around in the grease.Then make sure there is enough grease in the hub,where the bearing came out of.
How do you adjust the clutch on a 1995 Suzuki sidekick It slips bad?
If the clutch adjustment is correct, so that the clutch takes halfway through its travel, then it's time for a new clutch pressure plate/clutch plate/throwout bearing combo. One other reason might be grease on the existing clutch plate due to sloppy mechanic assembly.Or a combination of the two. New clutch time!
Have a 2000 Honda crv the clutch pedal squeaks when engaging didnt do this tilli put tranny in neutral now you havw squeaking when pedal goes in?
AnswerNot hearing your noise is a slight handicap for me, but my initial guess is that there is damage to the clutch release fork and/or release bearing. It is easier to tell when listened to, you may want a professional to take a listen. For help in finding a good tech, see the links on my bio page, or the related link I have added.ANSWERaplly some good grease on the slave cylinder-end steel ball,contact pointAnswerGENUINE HONDA PRO MOLY 60 PASTE CHECK THIS OUT THE,ITS MOLY GREASE PASTE THE GREASE WILL NOT MOVE AND DISSAPPEAR,ITS AMAZING
How do you remove the clutch pilot bearing on a 1993 Toyota 4WD with 3.0 V6 engine?
Pack it with heavy grease then find a bolt or dowel that fits the hole exactly and whack the dowl with a hammer. The hydraulic pressure will force out the bearing. Yer welcome.
