answersLogoWhite

0

No gasoline is reaching the primer bulb.

User Avatar

Wiki User

13y ago

What else can I help you with?

Related Questions

What is the fuel line routing for a primer bulb?

The fuel line routing for a primer bulb typically involves connecting the fuel line from the fuel tank to one side of the primer bulb, and then connecting another fuel line from the other side of the primer bulb to the carburetor. The primer bulb acts as a manual pump that helps to draw fuel from the tank into the carburetor to aid in starting the engine. It is important to ensure that the fuel lines are properly connected and free of any kinks or blockages to ensure proper fuel flow.


What is the fuel line routing on a poulan 2375?

The small line from the tank (with the fuel filter) goes to the top port of the carburetor. The large line from the fuel tank goes to the center port of the primer bulb. The other port of the primer bulb goes to the bottom port of the carburetor.


What is the correct fuel line hook up for a zama carbuator with a primer bulb?

Connection nearest bulb is return to tank.


Where is the in and out a primer bulb?

The "in" and "out" markings on a primer bulb indicate the direction of fuel flow. The "in" side typically connects to the fuel tank or line bringing fuel to the bulb, while the "out" side directs the fuel towards the engine or carburetor. Properly connecting these lines ensures the primer bulb effectively primes the fuel system for starting. Always refer to the specific equipment's manual for accurate installation guidance.


How do you replace poulan chainsaw fuel line?

I'm having the same problem with my Poulan chainsaw and weed eater. I think the line starts with the fuel filter in the tank and travels up to the primer bulb, out of the bulb into the carburetor, and out of the carburetor back to the tank. Whatever the size of line is that hooks to the fuel filter is what will hook to the primer bulb and then the carburetor. Then one more single line returns to the tank. I may not be correct on this, but there's not much information available. The diagram on Poulan's website does not show the routing of the fuel lines. that is right but to remove the main line you need to drain fuel and pull the line out from the fuel tank neck first because it has a connection that will not fit threw the hole in top. to replace it cut new line at a slaint and fir it threw from the top down into the fuel tank. then keep it long and pull out enough threw the fuel cap to put fitting back on it and fuel filter then pull it back threw and hook it to primer bubble. Not sure about your answer I have two different size fuel lines on mine. The larger line if I remember correctly runs from primer bulb to the right of fuel tank where the larger opening is located. The smaller line is where I am confused at shouldn't the smaller line from the fuel tank that has in tank filter attached run up to carburetor. then a smaller line from primer bulb to second fitting on carb. byrumjr the line starts with the fuel filter in the tank and travels up to the carburetor out of the carburetor into the primer bulb, out of the primer bulb back in the tank


Where is the carb connection on a primer bulb?

The carb connection on a primer bulb is typically located on the side of the bulb that connects to the carburetor's fuel intake. When the primer bulb is squeezed, it pushes fuel from the tank into the carburetor, helping to prime the engine for easier starting. The bulb usually has two connections: one for the fuel line from the tank and one that leads to the carburetor. Make sure to refer to your specific engine's manual for precise locations and configurations.


I inherited a mac 3216 chainsaw with no manual. The gas lines are rotted away of course The primer bulb connects to the carb and the other line goes to the tank but how does it end?

Here you go (just learned this the hard way): # 2 lines go to the fuel tank: 1 all the way to the bottom, this is the fuel supply line and should have a good fuel filter on it; the other should only go in to the tank 1/2" to 3/4", this is the fuel return # the above mentioned fuel supply line connects direct to the carb on the chain side of the saw # another third hose connects the carb (on the starter side) to the inlet valve of the primer bulb (this is the shorter protrusion of the primer bulb) # the outlet valve on the primer bulb connects to the fuel return hose that goes back to the tank good luck


How do you Route fuel lines on a Poulan chain saw?

long line with filter goes from gas tank into carb shorter line goes to (INLET) suction side of primer bulb 3rd line goes from OUTLET side of primer bulb to other carb fitting


Where do fuel line go on poulan chainsaw?

byrumjr the line starts with the fuel filter in the tank and travels up to the carburetor out of the carburetor into the primer bulb, out of the primer bulb back in the tank raylago fuel line routing is as follows for all 2 cycle with primer ball external to the carb. remember the fuel is sucked into the carb, not puished or blown into the carb. the filtered line from the fuel tank goes to the "in" side of the carb. this is usually right next to the high speed adjustment screw on a walbro carb. the "out" line from the carb goes to the suction side of the primer ball, the output of the primer ball goes back to the return line in the fuel tank. if you have to run the choke and the carb high speed screw will not adjust properly, reverse the in and out lines to the carb.


Briggs and stratton primer bulb not working?

You either have a bad bulb or a bad fuel line between the bulb base and the gas tank. If there is the slightest hole or crack in the bulb it will not work. They are easy to replace.


A diagram for fuel lines for a poulan woodshark 1950?

Make sure you have the lines wright the skiney line from in the tankgoes to the top nipple on the carb the over flow line goes to the long nipple on the primer bulb and the other line off the primer bulb goes to bottom nipple on carb


Why won't my Briggs and Stratton 4.5 HP lawn mower engine prime I have removed and cleaned the carb. The primer worked properly before disassembly. Now the bulb won't shoot fuel into the carb.?

The primer bulb probably needs to be replaced unless either one of the fuel hoses leading in and out of the primer bulb bracket is clogged. Be sure you mark how each fuel line goes before you remove the bulb so you can replace them correctly. Hmmm. Thinking more about it: If the primer worked properly before disassembly, chances are you crossed up the fuel lines when re-installing. Try switching them.