answersLogoWhite

0

If you are wanting to colaspe the piston so you can fit new pads in the caliper, first open the master cylinder, then use a "c" clamp or "c" clamp vise grips to slowly push the piston back enough to place the pads in and then fit caliper over your rotor.Keep in mind there may be a mess at the master cylinder.

User Avatar

Wiki User

16y ago

What else can I help you with?

Related Questions

How do you change the breaks on a 1995 Mustang Gt?

The rear brakes you need a 3/8 standard wrench to open two bolts retaining the caliper. The piston caliper requires a special tool to "wind " it or screw it back in order to install the new brake pads. DO NOT PRESS THE CALIPER PISTON BACK. You have to "screw" or rotate it. The rear brakes you need a 3/8 standard wrench to open two bolts retaining the caliper. The piston caliper requires a special tool to "wind " it or screw it back in order to install the new brake pads. DO NOT PRESS THE CALIPER PISTON BACK. You have to "screw" or rotate it.


Why is the brake caliper piston not retracting properly?

The brake caliper piston may not be retracting properly due to issues such as a seized piston, worn out seals, or air in the brake system. These issues can prevent the piston from moving back smoothly, affecting the brake performance.


How do you compress the rear brake piston on proton gen2?

You will need to wind the pistons in the calipers back in..there are wind back kits available online..note that the pistons wind back in different roations according to which wheel you are doing..passenger side rear winds in anti clockwise rotation while the drivers side rear winds in on a clockwaise rotation..


How do i push the rear caliper piston back?

To push the rear caliper piston back, you'll need a caliper tool or a C-clamp. First, remove the wheel and brake pads to access the caliper. Then, insert the tool or place the C-clamp over the caliper with one side against the piston and the other against the caliper body, and gently tighten it to push the piston back into the caliper. Make sure to check the brake fluid reservoir, as pushing the piston back may cause fluid to rise and overflow.


How do you reset the brake caliper of 2006 Acura TL?

To reset the brake caliper on a 2006 Acura TL, you typically need to retract the caliper piston back into the housing. This can be done using a brake caliper tool or a C-clamp to gently push the piston back in. Ensure the brake fluid reservoir cap is loosened to prevent pressure buildup. Once the piston is fully retracted, you can reinstall the caliper and brake pads as needed.


How do you push the piston back on rear caliper on 2005 mercury montego?

To push the piston back on the rear caliper of a 2005 Mercury Montego, you'll need to use a brake caliper tool or a C-clamp. First, ensure you have removed the caliper from the bracket and unhooked the brake line if necessary. Then, place the tool or C-clamp over the caliper piston and the back of the caliper, and gently compress the piston back into the caliper housing. Make sure to check the brake fluid reservoir and remove some fluid if necessary to prevent overflow during this process.


What tool do I need to push back the piston on the caliper of a 2002 Mitsubishi lancer?

You will need special brake caliper tool such as a C-clamp to push back the piston on the caliper of a 2002 Mitsubishi Lancer.


How do you compress caliper piston?

To compress a caliper piston, you can use a brake caliper tool or a C-clamp. First, ensure the brake fluid reservoir cap is loosened to avoid pressure buildup. Then, position the tool or clamp against the piston and the back of the caliper, and slowly apply pressure until the piston is fully retracted. Be cautious not to damage the piston or the caliper during the process.


How do you get piston in rear brake caliper to retract back into the caliper so you can change pads on a 2002 Mazda protege 5?

There is a 14 mm bolt on back of caliper. Remove this & use a 4 mm Allen wrench to back piston into caliper.


How do you change the front brake pads of a 2001 Jeep Wrangler Sport?

You will need a tool to wind back the caliper piston or a steering wheel puller will do the job.All the standard stuff choc wheels jack up front remove wheels .Remove the two bolts top and bottom at the back of the caliper remove the caliper remove the outer brake pad use the tool to wind back the piston all the way remove the inner pad and place new pads in replace caliper and bolts pump the brake pedal until hard and replace wheels .


How do you change the rear brake pads on a 2002 Volkswagen jetta?

How do you get the brake piston to retreat back in caliper ?


Kia SephiaMentor. When replacing rear brake pads does one have to push the caliper piston back as well as rotate it in a clockwize direction?

You will need to push the caliper piston back as well as rotated when you are replacing your rear brake pads. The caliper will need to be turned clockwise.