0
Disconnect the negative battery terminal. Under the hood is the relay/fuse box. (On the right if you're looking under the hood.) Take the top off and you'll see the fuse up front with two battery cables held by 10mm bolts. Take them off. When you do you'll see a nice sized plastic tab running down between where you took off the battery cables. It's taped to the wiring harness. Use a screwdriver to cut the tape off the tab. Then you can push on four obvious tabs to pull the whole fuse/relay box out. Once you do you'll see one of the two 10mm bolts on the bottom that hold the fuse in.One you can get a socket on,the other requires patience with a box wrench. It snaps back together, put the terminals back on and you're good.
What else can I help you with?
How do you change the main fuse in a 2003 Mazda Protege?
help
How do you change the main 120amp fuse in a 2002 Mazda Millenia?
remove the two nuts holding down the battery harness inside the fuse/relay center, then you can pull it out.
How do you change the main 120 amp fuse in a 2000 Mazda Millenia?
To change the main 120 amp fuse in a 2000 Mazda Millenia, first ensure the vehicle is off and disconnect the negative battery terminal for safety. Locate the fuse box, typically found near the battery or under the dashboard. Remove the old fuse using a fuse puller or pliers, and replace it with a new 120 amp fuse, ensuring it fits securely. Finally, reconnect the negative battery terminal and check that all electrical systems are functioning properly.
How do you change main 120 amp fuse in a 2000 mazda milena?
First, locate the fuse box. Then, once inside the fuse box, locate the 120 amp fuse. Remove it by pulling it straight out. Lastly, place the new one in place of the old one.
Where is the main fuse on a 2000 mazda miata?
The main fuse for a 2000 Mazda Miata is located in the fuse box, which is found under the dashboard on the driver's side. To access it, you'll need to remove the cover of the fuse box. The main fuse is typically labeled in the fuse box diagram, which can help you identify its specific location and amperage. Always ensure the car is turned off before checking or replacing any fuses.
How do you change the main fuse on a 1993 probe?
The Main fuse is in the fuse box under the hood on the drivers side. It is a 100 amp fuse.
Where is main igintion fuse on 1993 Mazda miata?
The main ignition fuse for a 1993 Mazda Miata is located in the fuse box under the dashboard on the driver's side. To access it, you'll need to remove the cover of the fuse box, and the ignition fuse is typically labeled in the diagram on the cover or near the fuses themselves. It's important to consult the owner's manual for the exact fuse location and specifications.
Why does the main fuse on your Mazda bongo keep blowing?
More than likely a short in the wiring.
What is the number of the main fuse on a 2004 Mazda 6?
The main fuse for a 2004 Mazda 6 is typically a 60-amp fuse located in the engine compartment fuse box. It is essential to consult the owner's manual for the exact location and specifications, as fuse layouts can vary. Always ensure the vehicle is off before checking or replacing fuses to avoid any electrical hazards.
How do you replace the main 100a amp fuse on a 1996 Mazda 626 4-cylinder?
Mazda main fuse is bolted in with two M10 bolts. I know because I destroyed mine while trying to remove it. You will need a good socket set with a universal joint to remove it.
Where is the dome light CPU on a Mazda 626?
The CPU for a dome light on a Mazda 626, and most other Mazda vehicles, is located near the main fuse box. This is found under the hood.
Main fuse on a harley 2003 road king?
it has a main circuit breaker in front of the battery
