0
1. undo the bleed valve on top of the sediment bowl, and pump the primer 10 times
then close the valve.
2. open the bleed valve on the 1rst fuel filter, (top valve) repeat pumping. close valve.
do the same to the bottom valve on the 1rst filter.
3. do the same to the secondary filter.
4. open the valve on the fuel pump(under the injector lines) pump and close it
5. do the same to the bottom valve.
6. if you have four injector fuel lines(four cylinder) undo two lines at a time and turn the key until straight diesel comes out, then reattach line. repeat with other two. then start the tractor.
if it doesn't work, you may have more air in the lines or another problem.
What else can I help you with?
How do you bleed a 265 Massey Ferguson tractor s fuel line?
To bleed the fuel line on a Massey Ferguson 265 tractor, first ensure the tractor is off and the fuel supply is turned off. Locate the bleed screw, typically found on the fuel filter or injector pump, and loosen it slightly. Then, turn on the fuel supply, allowing fuel to flow until it runs clear without air bubbles, and tighten the screw. Finally, start the tractor to ensure it runs smoothly.
How do you bleed the brakes on a Massey Ferguson 399 tractor?
To bleed the brakes on a Massey Ferguson 399 tractor, start by locating the brake bleeder screws on each brake cylinder. With the tractor parked on a level surface, have an assistant pump the brake pedal several times and hold it down. Loosen the bleeder screw to release any trapped air and fluid, then tighten it before your assistant releases the brake pedal. Repeat this process until you see a steady stream of brake fluid without bubbles, ensuring the brake system is fully bled.
How do you prime the fuel pump for a Massey Ferguson tractor?
To prime the fuel pump on a Massey Ferguson tractor, first ensure that the fuel tank has adequate fuel. Locate the fuel pump, typically near the engine, and check for any manual priming mechanism or bleed screw. If present, loosen the bleed screw slightly and turn the ignition key to the "on" position without starting the engine, allowing the pump to push fuel through until you see fuel without air bubbles. Tighten the bleed screw and try starting the engine.
How do you bleed injectors on a Ford-New Holland 1920 tractor?
you turn up the fuel pump
How do i bleed brakes on a 383 Massey Ferguson?
To bleed the brakes on a 383 Massey Ferguson, start by ensuring the tractor is on a level surface and the parking brake is engaged. Locate the brake bleeder valves on each brake assembly, typically found near the wheel. Using a wrench, open the bleeder valve slightly and have an assistant pump the brake pedal several times, then hold it down while you close the valve. Repeat this process until you see clear, bubble-free fluid coming out, and ensure to check the brake fluid level in the reservoir throughout the process.
How do you bleed the injectors on a Massey Ferguson 230 diesel?
Loosen the bolt on the top of the injector for cylinder #1, located on the left side front of the engine, under the fuel tank. Prime the system with the manual pump located on the right side of the tractor to the rear of the fuel filter and above the starter. Prime until clear fuel without air spills from the injector. Repeat for injectors 2 and 3. If you have someone to crank the engine, you can close and open each injector repeatedly. Close the injector, build pressure, then release. It takes a while, stay with it.
How do you bleed air from fuel system on Massey Ferguson 1540 diesel?
To bleed air from the fuel system on a Massey Ferguson 1540 diesel, first, ensure the fuel tank is full and check for any leaks in the lines. Then, locate the fuel filter and loosen the bleed screw on top to allow trapped air to escape while cranking the engine. Once fuel flows steadily without bubbles, tighten the bleed screw. Finally, crank the engine until it starts, ensuring there’s no more air in the system.
How do you bleed the power steering system of a Massey 650 diesel?
To bleed the power steering system of a Massey Ferguson 650 diesel tractor, you should fill the reservoir with the recommended fluid, start the engine, and turn the steering wheel from lock to lock several times. Make sure to check the fluid level periodically and top up if needed. Repeat the process until there are no air bubbles in the system and the steering feels smooth.
How do you bleed the hydraulic on 3600 ford tractor?
You do not need to bleed hydraulic systems on tractors.
How do you bleed the injectors on a 1996 Chrysler Town and Country?
The fuel injectors are self bleeding on a 1996 Chrysler Town and Country.
How do you bleed fuel injectors on 2000 Oldsmobile alero?
They are self bleeding.
How do you bleed the fuel line in a 3910 tractor?
How to get the air out of the fuel lines on a 3910 diesel tractor
