answersLogoWhite

0

Assuming that the compressor is a single phase unit, please do the following.Disconnect all the connections of the compressor. Using a good multimeter, measure the resistance between the 3 terminals. Lets call the terminals as A,B and C.

Measure the resistance between A-B, B-C and C-A in ohms. The lowest resistance will be between the Common and the Running Winding. The highest resistance will be between the Running and the Starting Winding.

In the above example, lets say A-B is 5 ohms, B-C is 10 ohms and C-A is 15 ohms. Then A-B is the running winding which means either A or B has the common terminal. As C-A is 15 ohms which means C-A has the starting and the running terminal, it is confirmed that B is Common. Hence, in ABC, A will be the running winding, B will be Common and C will be Starting winding.

Hope this helps

User Avatar

Wiki User

12y ago

What else can I help you with?

Related Questions

How do you test a Compressor if good on HVAC unit?

With an ohm-meter. Check for continuity in the RUN and START windings, and also from the terminals to compressor case for shorting. There should be continuity in the windings and no continuity from windings to compressor case.


Can bearings in a compressor be repaired?

No, not by the average home mechanic. Bad compressor? Replace the entire unit.


What causes compressor to lock out ina home ac?

what causes compressor lockout in voager rooftop unit.


Can you rebuild a compressor for home AC unit?

No the compressors in residential condensing units are called hermetic compressors and have to be rebuilt by cutting open the compressor shell, then rebuild the compressor and then weld the shell shut. Buy a new compressor or condensing unit.


How is central unit connected to the thermostat and the compressor unit?

In most residential systems, the home thermostat is connected to the interior air handler unit which is then connected to the exterior compressor.It is common to see control wiring from the compressor unit following a freon tube to the interior unit.


How can you tell if your home air conditioner compressor is bad?

You can determine if your air conditioner compressor is bad by checking for signs such as loud noises, inadequate cooling, or the unit not turning on at all. Additionally, if the compressor is overheating or if you notice refrigerant leaks around the unit, these could indicate a malfunction. A tripped circuit breaker or a burning smell may also suggest issues with the compressor. If you're experiencing these problems, it's best to consult a professional for diagnosis and repair.


Does the compressor come on if you have the fan only running on your home ac unit?

Yes your compressor comes when you set your thermostat to "Fan" setting and you have it on cool setting.


Where is the compressor located in an AC unit?

The compressor in an AC unit is typically located outside the building, near the condenser unit.


Where is the compressor located on an AC unit?

The compressor in an AC unit is typically located outside the building, near the condenser unit.


What size capacitor for this compressor unit?

To determine the appropriate capacitor size for a compressor unit, you need to check the compressor's specifications, particularly the rated voltage and the amperage. Typically, the capacitor size is expressed in microfarads (µF) and can range from 10 to 100 µF depending on the compressor's horsepower. It's also essential to consult the manufacturer's guidelines or a professional technician to ensure you select a capacitor that matches the compressor's requirements for optimal performance and safety.


Can you use 3 split ac unit on one compressor unit?

Up to 2 forced air units to one compressor unit.


How do you wire a run cap for an ac unit?

To wire a run capacitor for an AC unit, first, ensure the power is turned off to the unit. Identify the capacitor terminals, typically labeled "C" (common), "H" (high), and "L" (low). Connect the common wire from the compressor and fan to the "C" terminal, the wire from the compressor to the "H" terminal, and the wire from the fan to the "L" terminal. Finally, secure all connections and restore power to test the unit.