0
What else can I help you with?
How do you remove the water pump pulley on a 1985 Oldsmobile cutlass ciera?
pulley puller
How do you change 99 Oldsmobile silhouette crank sensor?
To change the crankshaft position sensor on a 1999 Oldsmobile Silhouette, first disconnect the negative battery cable to ensure safety. Locate the sensor, which is typically found near the crankshaft pulley; remove any components obstructing access. Disconnect the electrical connector and unscrew the sensor from its mounting position. Install the new sensor by reversing the steps, ensuring it is securely fastened and reconnected before reconnecting the battery.
Installing belts in 99 Oldsmobile Cutlass?
Begin by loosening the tensioner pulley on your 1999 Oldsmobile Cutlass. Put your serpentine belt around the pulleys. Tighten the serpentine belt with the tensioner pulley.
How do you adjust the tension pulley on a 2002 Oldsmobile alero?
it is self adjusting .
Why is crank pulley wobbling?
Crank pulley wobbling can occur due to several reasons, including a worn or damaged crankshaft, misalignment of the pulley, or a failing engine mount. Additionally, a loose or damaged harmonic balancer can contribute to this issue. It's essential to address the problem promptly, as it can lead to further engine damage or belt misalignment. If you notice wobbling, it's advisable to have a technician inspect the engine components.
Where is the crankshaft sensor on a 1998 Oldsmobile Bravada?
On front cover of engine by crankshaft pulley.
How do you replace a tensioner pulley on a 2000 Oldsmobile intrigue?
To replace the tensioner pulley on a 2000 Oldsmobile Intrigue, first, disconnect the negative battery terminal for safety. Then, use a wrench or socket to relieve tension on the serpentine belt by turning the tensioner pulley counterclockwise. Remove the old tensioner pulley by unbolting it and then install the new pulley in its place, securing it with bolts. Finally, reattach the serpentine belt, ensuring it's properly aligned, and reconnect the battery terminal.
How do you change idlers pulley on a 1997 Oldsmobile Aurora?
To change the idler pulley on a 1997 Oldsmobile Aurora, first, disconnect the negative battery cable to ensure safety. Then, remove the serpentine belt by using a wrench to relieve tension on the tensioner pulley. Next, unbolt the old idler pulley from its bracket, replace it with the new pulley, and secure it in place. Finally, re-install the serpentine belt, ensuring it's properly aligned, and reconnect the battery.
How do you install a bypass pulley on a 1990 Oldsmobile regency?
To install a bypass pulley on a 1990 Oldsmobile Regency, first, disconnect the negative battery terminal for safety. Remove the serpentine belt by loosening the tensioner pulley with a wrench, then take off the old pulley if it’s still attached. Install the new bypass pulley in place of the old one, ensuring it is securely fastened, and then re-route the serpentine belt over the new pulley. Finally, reconnect the battery terminal and check the belt alignment before starting the engine.
How do you replace the idler pulley on 1997 Northstar V8 in Oldsmobile aurora?
To replace the idler pulley on a 1997 Oldsmobile Aurora with a Northstar V8 engine, first, disconnect the negative battery cable. Remove the serpentine belt by using a wrench on the tensioner pulley to relieve tension. Then, unbolt the old idler pulley from its mounting bracket and replace it with the new pulley, ensuring it’s securely fastened. Finally, re-install the serpentine belt and reconnect the battery cable.
Picture of 97 Oldsmobile achieva serpentine belt on the pulleys?
Serpentine belt and pulley diagrams at www.alldatapro.com
Where is the harmonic balancer on 1997 Oldsmobile aurora 4.0 v-8?
bottom pulley. at end of crank.
