To fix the backup lights on a 1998 Isuzu Trooper, start by checking the bulbs to ensure they are functioning. If the bulbs are fine, inspect the fuse related to the backup lights in the fuse box, and replace it if blown. Next, examine the backup light switch, usually located on the transmission, to ensure it is working properly and making a good connection. If these components are functioning but the lights still don't work, there may be an issue with the wiring that needs further investigation.
wear gloves, bearings all come out. then you have to remove the sensor off the back of it. along with 6 17mm bolts. How do you change the rotors in the front on a 1998 Isuzu Trooper
I have 1998 Trooper. I called Isuzu and they were very helpful. Open the back door, above the cable that holds the wiring for the back light there is a screw. Unscrew it and then unscrew the 2 screws that are on the outside. My light was out on the driver's side but it is probably the same on the passenger side. When you are screwing it back together, do the outside screws first then the inside one. Good luck. It took me 5 minutes to do.
you have two seats in the front, and a bench seat in the back
To replace the headlight assembly on a 1998 Isuzu Trooper, first, open the hood and remove the screws or bolts securing the headlight assembly, typically located at the top and side. Disconnect the wiring harness from the back of the assembly and carefully pull the old assembly out. Insert the new headlight assembly, reconnect the wiring harness, and secure it with the screws or bolts. Finally, test the new headlight to ensure it functions properly.
To reset the alarm system on a 1998 Isuzu Trooper, first ensure the vehicle is unlocked using the key. Insert the key into the ignition and turn it to the "On" position without starting the engine. Then, press and hold the "Unlock" button on the driver's side door while turning the ignition to "Off" and back to "On" again. This should reset the alarm system. If issues persist, consult the owner's manual for specific instructions or consider seeking professional assistance.
To replace the right front marker light on a 1998 Isuzu Trooper, first, ensure the vehicle is turned off and the keys are removed. Open the hood and locate the marker light assembly; then, remove the screws or clips holding the assembly in place. Carefully pull the assembly out, disconnect the wiring harness, and replace the old bulb with a new one. Reconnect the wiring, secure the assembly back in place, and test the new light to ensure it works.
You can find the PCV valve, on the outside of the air cleaner housing. The PCV valve will be attached to the back of the housing.
i have a 1990 Isuzu trooper as well and the speedometer and odometer also quit working, they both come off of a mechanical cable that is attached to the drive train. that cable breaks, and you lose both speed and odometer indications. they are extremely difficult to find, so if you do, write me back...
To tighten the belt on a 1990 Isuzu Trooper, first locate the tensioner pulley. Use a wrench or ratchet to turn the tensioner arm, which will relieve tension on the belt. Once the belt is loose, inspect it for wear and proper alignment, then reposition or replace it as needed. Finally, release the tensioner to tighten the belt back into place, ensuring it is secure on all pulleys.
If a smog inspector said that the EGR EVAP and Fuel Pressure sensor are modified on a 1988 Isuzu Trooper II 2.6, then the problem has to be fixed before the smog inspector will approve the vehicle for registration. The EGR EVAP and Fuel Pressure Sensors have to be put back the way they came from the factory.
THE FUEL PUMP ON THE 1986 ISUZU TROOPER 2 GAS 2.3 ENGINE IS LOCATED UNDER THE INTAKE MANIFOLD. YOU CAN GET TO IN BY TAKING OFF THE FRONT PASSENGER WHEEL AND RUBBER GARD AND YOU WILL SEE IT. I HAVE ONE OF THESE TROOPERS. HOPE THIS HELPS.
The EGR (Exhaust Gas Recirculation) valve on a 1985 Isuzu Trooper is typically located on the engine intake manifold, near the back of the engine. It connects to the exhaust manifold via a metal pipe. To access it, you may need to remove some components such as the air intake or other hoses for better visibility and reach. Always refer to a repair manual for specific details related to your vehicle's configuration.