0
To reconnect the AC hose to the condenser on a 2004 Pontiac Vibe, first ensure the system is discharged and safe to work on. Align the hose fitting with the condenser port, making sure the O-ring is in good condition to prevent leaks. Push the hose onto the port until it clicks into place, then secure it with the retaining clip if applicable. Finally, check for proper connection and any signs of leaks before recharging the AC system.
What else can I help you with?
Where is orafice tube on Pontiac gran am?
What year? On a 2002, take the discharge hose from the condenser apart and you should find it in the hose end.
Where is the air conditioner evaporator drain hose located for a 2004 Pontiac Vibe?
it is in the passenger side front floorboard at the top left. A Short elbow shaped hose should be connecting from the condenser out through a drain hole in the body/frame. If it disconnects, you'll get water in your floorboards when you run your A/C
Where is the radiator drain puly on a 2004 Pontiac gto?
In order to drain the radiator on a 2004 Pontiac GTO it is necessary to pull the lower radiator hose off. There is not a separate drain plug on this radiator.
Where to find step by step instructions to replace the air conditioning condenser in a 2005 gmc canyon?
Drain the cooling system.Remove the radiator.Recover the refrigerant.Remove the receiver dryer.Remove the condenser inlet hose bolt.Remove the condenser inlet hose.Remove the condenser outlet hose bolt.Remove the condenser outlet hose.Remove the condenser from mounts on the radiator.Remove the condenser...........................
How do you change a pressure hose on Pontiac Grand Am?
To change the pressure hose on a Pontiac Grand Am, first, ensure the vehicle is safely elevated and supported. Disconnect the negative battery terminal, then locate the pressure hose connected to the power steering pump and the steering gear. Use appropriate tools to loosen and remove the old hose, then install the new hose by tightening it securely. Finally, reconnect the battery, refill the power steering fluid, and check for leaks.
How much is a water hose for 1993 Pontiac grand am?
how do i replace a water hose in 1993 pontiac grand am
Where is the AC condenser drain hose in a 97 Jetta?
The 1997 VW Jetta air conditioning condenser drain hose can be found on the bottom of the air conditioner compressor. The drain hose will direct condensation to the bottom of the engine compartment.
Engine diagram for 1997 Pontiac grand am gt?
Where are the vacuum hose located at on '97 Pontiac grand am? Where are the vacuum hose located at on '97 Pontiac grand am?
How do you change thermostat in 1995 Pontiac Sunfire?
To change the thermostat in a 1995 Pontiac Sunfire, begin by ensuring the engine is cool, then disconnect the negative battery cable. Drain the coolant from the radiator and remove the upper radiator hose connected to the thermostat housing. Unbolt the thermostat housing, remove the old thermostat, and clean the mating surfaces before installing the new thermostat along with a new gasket. Reassemble the housing, reconnect the hose, refill the coolant, and reconnect the battery.
Where s the thermostat on 2004 Pontiac Montana van?
follow the driver's side rad hose back from the rad. you will find it mounted on the side
How do you replace a thermostat on a 2004 Kia Rio?
To replace the thermostat on a 2004 Kia Rio, first, ensure the engine is cool and disconnect the negative battery cable. Drain the coolant and remove the upper radiator hose connected to the thermostat housing. Unbolt the thermostat housing, take out the old thermostat, and clean the mating surfaces. Install the new thermostat, reassemble the housing, reconnect the hose, refill the coolant, and reconnect the battery.
How do you replace a thermostat in a 2004 Nissan Maxima?
To replace the thermostat in a 2004 Nissan Maxima, first, ensure the engine is cool and disconnect the negative battery cable. Drain the coolant and remove the upper radiator hose, then unbolt the thermostat housing. Replace the old thermostat with a new one, ensuring the gasket is in place, reassemble the housing, and reconnect the hose. Finally, refill the coolant, bleed the system of air, and reconnect the battery.
