answersLogoWhite

0

What else can I help you with?

Related Questions

Yamaha wr correct way to remove water pump impeller?

Remove the side case and the water pump. Remove the right side case, and remove the impeller and shaft. Holding the back side of the impeller shaft with a wrench on the flat spots, you can now twist the impeller off.


How do you change the impeller on a 9.8 mercury outboard?

The impeller on a 9.8 Mercury outboard boat motor can be easily changed. Remove the retaining bolt. The impeller will come off. Reverse the process to install the new impeller.


How do you change the impeller on the water pump on your 35 horsepower evinrude outboard boat motor?

First, remove the lower unit (there is a housing for the water pump). The drive shaft goes through the housing and turns impeller. Remove the housing, the impeller is on the shaft. Install the new impeller. When replacing the housing, turn the drive shaft clockwise to make it slide down over the impeller.


How would i un seize a 97 xp sea doo 2 stroke motor?

remove the jet pump and insert the impeller tool into the pto flywheel. Remove spark plugs and put some lubricant down the spark plug hole and try to turn the engine over with a breaker bar on the impeller tool.


How do you change impeller on 1966 Mercury 6hp twin?

First remove spark plug wires from plugs so engine does not start unexpectedly. Second remove lock nut under the trim tab just above the prop. There is also a metal screen this nut holds to strain the cooling water going into the engine. Next remove the lock nut just above the lower unit. This will also help split the lower unit away. next remove lower unit watching for the water pickup tube. Place lower unit in a secure area and remove the two nuts holding the plastic cover down. Then remove the 2 o rings on the drive shaft so plastic housing can be taken off. Remove metal plate over water impeller. Remove old impeller watching for the small pin that the drive shaft uses to turn the impeller. use a little motor oil on the new impeller. Replace metal cover and plastic housing while turning drive shaft clockwise. Press down replace lower unit.


What is the name of the tool you used to remove the valve from the tire?

shredder valve.


Where is the Volvo penta impeller located?

The impeller in a Volvo Penta is located inside the water pump. You will need to first remove the water pump to access it.


How do you change impeller on Chrysler outboard?

Its not that hard all you have to do is take the five bolts out of the lower unit and disconect the shift linkage, then you just pull the lower unit from the engine and you have the cover that slides onto the driveshaft remove the 4 bolts from it and pull it off and there is your impeller istalation is reveres of removal


How do you remove impeller on godwin pump CD 150?

To remove the impeller on a Godwin CD 150 pump, first ensure the pump is powered off and disconnected from any power source. Next, remove the pump casing by unscrewing the bolts that secure it, and then carefully lift it off to access the impeller. Use a suitable tool, such as a puller, to gently extract the impeller from the shaft. Make sure to follow any specific manufacturer guidelines or safety precautions during the process.


How do you take an impeller off a hayward power flo lx pool pump?

To remove the impeller from a Hayward Power-Flo LX pool pump, first turn off the power and disconnect the pump from the electrical supply. Next, remove the pump's front cover by unscrewing the screws, then take out the diffuser to access the impeller. Use a socket wrench to unscrew the impeller by turning it counterclockwise, and be cautious of any debris that may have accumulated. Once removed, inspect the impeller for damage or wear before replacing or cleaning it.


How do you change the water impeller on a 9.9 hp Tomos traveler?

To change the water impeller on a 9.9 hp Tomos Traveler, first ensure the engine is off and cooled down, then remove the lower unit by unscrewing the bolts that secure it. Once the lower unit is detached, take out the old impeller from the water pump housing. Clean the housing, install the new impeller ensuring it is oriented correctly, and reassemble the lower unit by reversing the disassembly steps. Always refer to the specific service manual for detailed instructions and torque specifications.


How do you unlock a Fellowes Shredder model DS-7400C?

How to remove the collection box from the machine to empty