0
As a tech who worked for a fleet which operated the T660 as its mainstay until recently (when they fell out of favor for the T680), I'll guide you right through this.
On the right hand (passenger) side of the vehicle, under the hood, and against the firewall, you'll see the HVAC compartment. On that compartment, you'll see a plate which is held in with four bolts... the top two are recessed further back than the bottom two. You'll remove those with a 10mm socket.
Once you've done that, CAREFULLY remove that plate - the blower motor is attached to it, and the wires are attached to the blower motor. The wires are attached with simple slide-in fittings, so they'll be easy to detach - just gently pull them apart.
Once you've done that, you pull the whole assembly out.
Remove the fan wheels by gently pressing them out... they do break easily, mind you, and if you don't feel like replacing them, you want to treat them with the kid gloves. Be mindful also that there are arrows on each one showing the direction its intended to spin... you want to reinstall them the same way on the new blower motor.
There's a metal clamp holding the blower motor to the plate... I don't remember off the top of my head what size socket and wrench you'll need for it, but it's a bolt with a nut and washer to hold the clamp shut... maybe it's 10mm? I remember how to do these, but it's been a while, so I don't remember offhand exactly what size sockets are needed, but I'm fairly certain they're all metric.
The last bolt you need to remove will be a much smaller one, and it's what attaches the blower motor wiring harness to the assembly.
Installation is the opposite of reverse, just bear in mind that you'll probably have to fidget a little with that plate when putting it back in order to get the bolt holes lines back up properly.
You are free to direct any questions arising directly from this answer to the email address listed on my bio page, but please post any questions not related to this answer as community questions - if you post them under the "Cars and Vehicles" or (preferably) "Commercial Vehicles" categories, you can be assured they will be seen and replied to, especially pertaining to the T660, whether with the Cummins ISX or PACCAR MX engine.
What else can I help you with?
How do you replace the blower motor resistor on a 2010 kenworth t370?
To replace the blower motor resistor on a 2010 Kenworth T370, first, disconnect the negative battery cable to ensure safety. Locate the blower motor resistor, typically found near the blower motor under the dashboard on the passenger side. Remove the electrical connector and unscrew the resistor from its mounting position. Install the new resistor by reversing these steps, ensuring the connector is securely attached before reconnecting the battery.
Where is blower motor 2010 Nissan rogue?
where is the blower motor on a nissan rogue
Why does my blower motor stop working in 3rd gear on a 2010 explorer?
The issue may be caused by a faulty blower motor resistor.
What to do if car ac wont blow any air?
where is resistor pack on 2010 impala lt 6 cylinder 3.5 motor
What could stop the blower motor from working in a 2010 Ford Fusion?
One thing that could stop a blower motor from working correctly in a 2010 Ford Fusion is a blown fuse. Another thing that might be stopping the blower from working is a broken fan.
Why is your blower not working in your 2010 dodge avenger?
If the blower in your 2010 Dodge Avenger is not working, it could be due to a blown fuse, a faulty blower motor, or a malfunctioning blower motor resistor. Additionally, issues with the climate control settings or a clogged cabin air filter may also affect blower performance. It's advisable to check the fuse first and then test the blower motor and resistor for any defects. If these components are functioning properly, further diagnostic may be needed to identify the problem.
What are the release dates for Whistle Blower - 2010?
Whistle Blower - 2010 was released on: USA: 14 October 2010 (Jacksonville Film Festival)
How do you turn off footwell lights in a 2010 kenworth t660?
The switch will be below and to the left of the steering column.
Where is the cabin air filter on a 2010 Ford Explorer?
Does a 2010 Ford Explorer have a cabin air filter? If it does, I can't find it. I removed the cover next to the wipers on the passenger side and only found a permanent unremovable wire screen over the blower. I also removed the glove compartment and didn't find anything behind it but the blower motor itself.
Where is the blower fan relay on a 2010 Honda CRV?
The blower fan relay on a 2010 Honda CR-V is located in the under-hood fuse box. To access it, open the hood and locate the fuse box, which is typically near the battery. The relay is usually labeled on the cover of the fuse box, and you can identify it by looking for the relay associated with the HVAC system or blower motor. If you're having trouble, consult the owner's manual for specific details and diagrams.
What actors and actresses appeared in Whistle Blower - 2010?
The cast of Whistle Blower - 2010 includes: Andrea Erkelens as Enslin Robert Hugh Brown as Hanns Schleyer
How do you replace blend door motor on Ford Fusion 2010?
To replace the blend door motor on a 2010 Ford Fusion, first disconnect the negative battery terminal and remove the dashboard trim to access the actuator. Next, locate the blend door motor, which is typically behind the glove compartment; unscrew and disconnect the electrical connector. Remove the old motor and install the new one, ensuring it is properly aligned, then reassemble the dashboard trim and reconnect the battery. Finally, test the operation of the new motor to ensure proper functionality.
