0
What else can I help you with?
How do you replace shift cable on 1998 Oldsmobile silhouette?
To replace the shift cable on a 1998 Oldsmobile Silhouette, first, disconnect the negative battery terminal for safety. Then, remove the center console to access the shift cable, detaching it from the shifter and the transmission linkage. Install the new shift cable by reversing the removal steps, ensuring it is properly secured and connected. Finally, reassemble the center console and reconnect the battery.
How do you replace the bushing on the shift cable for 1999 Oldsmobile silhouette?
To replace the bushing on the shift cable for a 1999 Oldsmobile Silhouette, first, ensure the vehicle is in park and the ignition is off. Remove the shift cable from the transmission and the shifter assembly by detaching any clips or retaining rings. Replace the old bushing with a new one, ensuring it's securely in place, and then reattach the shift cable to both the transmission and shifter assembly. Finally, check the cable alignment and operation before securing everything back in place.
How do you replace the hood release cable on a 1999 Honda Civic?
The hood release cable snakes into the cabin of the car through the firewall. To replace the cable remove the old wire. Zip tie the new cable to the old one and pull it out. This will easily snake the new cable into place. Install the new cable on the release and lever.
How do you change the shifter cable on a 1998 oldsmbile silhouette?
To change the shifter cable on a 1998 Oldsmobile Silhouette, first you need to disconnect the cable from the shifter, then disconnect it from the engine's control arm. Then replace it with the new cable and make sure it is functioning.
How do you fix the speedometer on a 1994 olds 98?
You can fix the speedometer in your 1994 Oldsmobile 98 by replacing the speedometer cable. If changing the speedometer cable does not fix your speedometer you will need to replace the entire speedometer.
How do you replace 1998 Oldsmobile silhouette auto trans shift cable?
To replace the auto trans shift cable on a 1998 Oldsmobile Silhouette, first, ensure the vehicle is parked on a level surface and the ignition is off. Remove the center console to access the shift cable connection at the gear shifter and disconnect it. Next, follow the cable to the transmission, detach it from the transmission lever, and remove any retaining clips. Install the new cable by reversing the steps, ensuring all connections are secure before reassembling the console.
Where is the speedometer cable to a 1990 olds cutless sierra?
There isn't a speedometer cable. There is a speedometer sensor,where it is located I am still trying to find out. On the tranny or in the speedometer or somewhere else?
How do you adjust the hood release cable on a 1996 GMC Sierra?
you have to replace it
How do you replace hood release cable on 69 Corvette-hood is closed?
== ==
How do you replace the tensioner pully on an Oldsmobile 88?
To replace the tensioner pulley on an Oldsmobile 88, first, disconnect the negative battery cable to ensure safety. Then, locate the tensioner assembly and use a wrench to relieve tension on the serpentine belt before removing it. Next, unbolt the old tensioner pulley from the assembly, replace it with the new pulley, and reassemble by reversing the steps. Finally, reattach the serpentine belt and reconnect the battery cable.
How do you remove or replace the bonnet release cable on a au Falcon?
To remove or replace the bonnet release cable on an AU Falcon, first, locate the release mechanism inside the car and pull the cable to release the bonnet. Next, access the cable by removing any necessary panels or trim to reach the cable's attachment points. Disconnect the old cable from the release mechanism and bonnet latch, then install the new cable by reversing the process, ensuring it is securely fastened and properly routed. Finally, test the new cable to ensure it operates smoothly.
How do put back throttle cable on a 94 Oldsmobile?
To put back the throttle cable on a 1994 Oldsmobile, first, locate the throttle body and identify the cable attachment point. Release any tension on the cable by pressing the accelerator pedal fully. Slide the cable end into the throttle lever, ensuring it clicks into place, then adjust the cable's tension if necessary. Finally, secure any clips or brackets that hold the cable in place and test the throttle operation.
