0
It's easy, but you'll need a helper. Once you have a replacement ready to go, find a socket that fits the pulley bolt on your old one. Ensure that there is a belt routing diagram under the hood or take a couple photos or draw one before you take off the belt. Use a long handle socket wrench to pry on the pulley against spring tension using bolt to create slack in the belt. At the same time have your helper slip it off one of the top accessories with a screwdriver. Once belt is off, remove bolt that holds tensioner bracket to block. Reverse to reinstall except this time your helper will be trying to put belt over last accessory while you hold pulley. Bump the engine a few times before you start it to ensure ribs on belt backside have all fallen into their grooves.
What else can I help you with?
Can't loosen idler tension pulley on air conditioner idler pulley?
Replace the tensioner assembly as one piece.
WHAT PULLEY DO I loosen to get single drive belt on?
If you are referring to the Serpentine belt, you loosen no pulley. You simply remove tension from the belt. The tension is applied by the Idler Pulley. Pry the idler back and remove the belt.If you are referring to the Serpentine belt, you loosen no pulley. You simply remove tension from the belt. The tension is applied by the Idler Pulley. Pry the idler back and remove the belt.
How do you replace a BMW E36 alternator belt?
Release the tension using a wrench etc from the idler pulley.
Why you use idler pulley?
To apply tension
Why would 98 ford Taurus be making noise if you changed the serpentine belt idler pulley and tension pulley?
replace the belt with a goodyear bet
When to replace upper and lower idler pulleys?
only if the idler arm will not hold the tension on the belt and the pulley needs replaced when the are warn sharp or warn flat
How do you replace the idler pulley on 1992 350 engine?
Remove the old, damaged idler pulley and replace it with a new one.
How do you replace the idler pulley on a 1993 Geo Prism?
I assume you mean the idler pulley on the A/C belt. I have not replaced this particular item but it should be simple. Looking from the top of the engine compartment on the passenger side you will see the idler pulley with a mounting/locking bolt which attaches the pulley and the tension adjusting point immediately above it. Loosen the pulley locking bolt by turning counter clockwise. Relieve belt tension by turning the adjuster bolt counter clockwise. Remove the belt and pulley. Replace in the reverse order.
Do you need to know what the torque would be to find out if the idler tension pulley has to be torqued when you install the serpentine belt on a 1995 Oldsmobile Cutlass Supreme?
there is not a specific torque for the idler pully. tighten it up with a ratchet and it will not loosen up
How do you replace the idler pulley on a 1997 dodge caravan?
Remove the belt, then remove the bolt holding in the idler pulley.
How do you change the serpentine belt idler pulley ona 2006 Isuzu ascender?
Requires two person team. Step One: Look at serpentine belt diagram on front of engine. Arrow points to idler tension pulley. (Front Left side of engine) Loosen this 15mm bolt. Step Two: Loosen Idler pulley bolt - 15mm. Step Three: One person push down on idler tension pulley with tire removal tool or cheater bar on front left of engine while second person lifts belt off alternator. Step Four: Remove Idler pulley and replace with new one. Tighten bolt to idler pulley Step Five: One person push down on idler tension pulley with while the other fits belt on alternator and around idler pulley. Step Six: Make sure belt fits as noted on belt diagram and Tighten bolt on idler tension pulley (front left side of engine). Approximate time: 10 minutes
How do you replace an idler pulley on a 2.4 Dodge Avenger 2008?
To replace the idler pulley on a 2008 Dodge Avenger with a 2.4L engine, first, disconnect the negative battery terminal for safety. Then, remove the serpentine belt by using a ratchet or a serpentine belt tool to relieve tension on the tensioner pulley. Next, unbolt the idler pulley from its mount using the appropriate socket size, and replace it with the new pulley. Finally, reattach the serpentine belt, ensuring it is properly routed, and reconnect the battery.
