0
Sharp, noisy blue flame=too much air
Blue flame with defined inner lighter blue cone= just right
Soft blue flame with yellow tips=not enough air, or using LP gas
Most times can be adjusted with the primary air shutter on the burner tube, being careful to check for good ignition after adjustment.
Caution: a yellow flame can carbon/clog up the heat exchanger eventually.
What else can I help you with?
What does a yellow flame indicate on a gas furnace?
its hot!
How can I fix an orange flame on my gas furnace?
To fix an orange flame on your gas furnace, you should first check for any blockages in the burner or air intake. Clean or replace any dirty components. Adjust the air-to-gas ratio to ensure a blue flame, which indicates proper combustion. If the issue persists, contact a professional technician for further inspection and repairs.
What is the function of a gas furnace flame sensor and how does it contribute to the proper operation of the heating system?
The function of a gas furnace flame sensor is to detect the presence of a flame in the furnace. It contributes to the proper operation of the heating system by ensuring that the gas valve remains open only when a flame is present, preventing the release of unburned gas and ensuring safe and efficient heating.
How big is a flame on a natural gas furnace?
The pilot flame is/should be about 1.5" long, the diameter of a pencil. When the burners are going, the gas is shot into the burner manifold, and the gas sent to the burner is designed to go to the back of the heat exchanger. So, in a typical 80,000 input heater, about 14"-18" long.
Why does the furnace igniter glow but no flame is produced?
The furnace igniter may glow but not produce a flame due to issues such as a clogged burner, a faulty gas valve, or a malfunctioning flame sensor. These problems can prevent the gas from igniting properly, leading to the lack of a flame.
How does a gas furnace pilot flame stay burning?
A gas furnace pilot flame stays burning by receiving a constant flow of gas from the pilot light assembly. The pilot light assembly contains a thermocouple that detects the presence of the pilot flame. If the flame goes out, the thermocouple signals the gas valve to shut off, preventing any gas leaks.
Where is the furnace pilot located?
The gas furnace pilot (flame is lit all the time) is sometimes referred to as a pilot light, but no matter what you call it, its purpose is to serve as a small ignition flame for the gas burner. And when this little flame fails to operate properly or go out, it's one of the most common reasons a gas furnace will fail to operate.
Seguence of operation for a direct ignition gas furnace?
If the furnace is direct ignition, The HSI or spark ignites the flame. A flame sensor passes current through the flame, if current is present the main.
How is fuel supplied to the pilot assembly on a gas furnace?
In a gas furnace, fuel is supplied to the pilot assembly through a gas line that connects to the gas valve. When the thermostat calls for heat, the gas valve opens, allowing gas to flow to the pilot assembly. The pilot, which is a small flame, ignites the gas, creating a flame that can then light the main burners when the furnace is operating. This process ensures that the furnace operates efficiently and safely.
On a gas furnace what energizes the blower motor in heat mode?
flame sensor
What is the function of the flame sensor on a furnace and how does it contribute to the safe and efficient operation of the heating system?
The flame sensor on a furnace detects the presence of a flame when the burner is ignited. It ensures that the burner stays lit and shuts off the gas supply if no flame is detected, preventing gas leaks and potential hazards. This contributes to the safe and efficient operation of the heating system by ensuring that the furnace operates properly and does not pose a risk of fire or gas leaks.
How does flame rectification works in a gas furnace?
Flame rectification in a gas furnace involves using an electrical signal to detect the presence of a flame. When a flame is established, the electrical properties of the flame change, allowing the sensor to confirm its presence. This signal is used by the control system to ensure the furnace continues to operate safely and efficiently.
