0
What else can I help you with?
How do you adjust the nozzle opening pressure of injector on diesel engines?
by rotating the ring which cover the opening of the nozzle
How do you avoid to put petrol into diesel car?
You avoid it by looking carefully at the fuel pump and making darn sure you are using the diesel nozzle which is larger than a petrol nozzle.
What is the tolerance between the nozzle needle and the nozzle body of a common rail diesel injector?
Find out who makes the engine and ask them
Car takes petrol or diesel?
Look at the fuel nozzle insert. If its green it petrol (unleaded),,,,, black diesel.
What is the thing next to your kitchen faucet?
The thing next to your kitchen faucet is typically a soap dispenser or a sprayer nozzle for washing dishes.
Why does your sub zero water dispenser spray when dispensing?
A Sub Zero water dispenser may spray while dispensing due to a few common issues. One possibility is that the water pressure is too high, causing the water to exit the nozzle forcefully. Another reason could be a faulty or worn-out seal or nozzle that allows water to escape in unintended directions. Lastly, if the dispenser is not aligned properly or if there is air in the lines, it may also lead to spraying.
How do you open the purell hand sanitizer dispenser?
Un-screw the top nozzle by turning it anti-clockwise and it should spring open with a slight pop.
What is the exit diameter of a GTAW gas nozzle with the 10 shown on it?
The exit diameter of a GTAW (Gas Tungsten Arc Welding) gas nozzle marked with a "10" typically indicates a diameter of 10 mm. This size is part of a standardized system used to designate nozzle sizes in gas tungsten arc welding applications. The selection of nozzle size can affect gas coverage and weld quality, making it important to choose the appropriate size for the specific welding task.
Can diesel be used in kerosene wick stove?
Diesel is a different grade of kerosene and will work. You may need to change the nozzle so it burns clean.
How to Clean an Automatic Soap Dispenser?
Installing an automatic soap dispenser in a home bathroom or kitchen is becoming a popular choice. It will free up clutter that collects around a sink, eliminate soap from dripping out of a pump, and is a healthier option to remain free of nasty bacteria that can build up around a soap dish. Even though these are a cleaner option for your bathroom or kitchen, the dispenser will need to be cleaned every now and then. Here’s how you can do this without much effort. You Will Need: Clean sponge Plastic zippered bag Vinegar Old toothbrush (optional) 1. Wipe it Down Start by wiping down the dispenser with the clean sponge. You can do this with just a little bit of water, enough to dampen the sponge without saturating it. You may need to use an old toothbrush to get the hard to reach areas. If your dispenser opens, you can open it and remove the soap pouch to make this task easier. 2. Clean the Nozzle The nozzle on a soap dispenser can become clogged with use. The soap will build up over time, making it harder for the dispenser to pump. If you aren’t able to clean the nozzle with just a sponge, you can use vinegar. White distilled vinegar works the best, but using an apple cider vinegar will reduce the amount of time you have to deal with the lingering odor vinegar leaves. You can place a little bit of vinegar in a plastic zippered bag, and place the nozzle in the bag. If the nozzle can’t be removed you can tie the bag up around the nozzle. This doesn’t need to sit for very long, just 10 or 15 minutes. Rinse the nozzle well, and it should be cleared up. 3. Clean the Interior The interior of a soap dispenser can get pretty grimy as well. This should be done each time you refill the dispenser. You will want to get rid of any soap that is in the dispenser pump, and rinse it well. Allow it to dry completely before you place the pump back. This will ensure mildew and bacteria can’t build up inside the pump. Now you can put your dispenser back together and begin using it again.
Why would fuel not go into the fuel tank?
Check and ensure that you are not trying to put diesel in the vehicle, diesel nozzles are larger diameter to prevent accidentally putting diesel in a vehicle that requires gasoline. If the incorrect nozzle is not the problem, lay on your back under the vehicle by so that you can see the area where the filler tube is and look for kinks, cracks or a broken filler hose between the tank and the where you put the gas in the car.
What is the exit diameter of a number 4 size gas tungsten arc welding nozzle?
1/4"
