0
The size of the bolt that holds the rear brake drum can vary depending on the make and model of the vehicle. Common sizes for these bolts are typically 10mm, 12mm, or 14mm, but it's best to consult the vehicle's service manual or specifications for exact details. Additionally, torque specifications for these bolts should be followed to ensure proper installation.
What else can I help you with?
Is there something holding rear brake drum on 1994 caviler what holds rear brake drum on 1994 cavalier after removing tire?
how to remove rear brake drum on 1994 cavalier
How do you adjust the hand brake on the rear drum of a Renault clio 1995?
To adjust the hand brake on the rear drum of a 1995 Renault Clio, first, ensure the vehicle is securely lifted and supported. Remove the rear wheel and the drum to access the brake assembly. Locate the adjusting wheel or screw mechanism inside the drum; turn it to either tighten or loosen the brake shoes until they make slight contact with the drum. Finally, reassemble the drum and wheel, and test the hand brake to ensure it holds the vehicle securely.
What torx size for the brake calipur?
what size torx bolt holds the rear parking brake housing on the 2005 chrysler pacifica
How do you remove the Rear brake pads?
AnswerIf you are asking how do you remove the rear drum to get to the pads there are some bolts on the back side of the drum that hold it on. I believe there is also another small bolt that holds on some brake component/sensor that must be removed. Once this is done, the drum will pull right off. When loosing the bolts on the back of the drum, be sure not to loosen the bigger bolts on the back of the spindle. Those bolts keep the entire wheel from flying off your car on the freeway! Those are actually the spindle nuts, which bolt onto your chassis to hold the wheel on the car.
How do you remove rear brake drum from a 1993 Toyota pickup?
How do you remove rear brake drum from a 1993 Toyota pickup?
How do you remove rear brake drum on a 2004 suzuki XL-7?
how do you remove rear brake drum on a suzuki 2004 xl7
How do you remove the rear brake drums from a 1995 Mazda Protege?
You need to remove the two Phillips head screws holding brake drum assembly on. Then thread an 8mm bolt through threaded hole on face of drum. This will push drum assmembly off of hub.
What is the purpose of a drum brake?
The purpose of a drum brake is to come to a complete stop with any veichle that may have drum brakes in the rear of the car.
How to adjust the Parking Brake on a 2006 GMC 3500 savana Where can i find the adjusting bolt?
To adjust the parking brake on a 2006 GMC Savana 3500, first, ensure the vehicle is on a level surface and the wheels are chocked. The adjusting bolt is typically located on the rear of the brake assembly, near the rear axle, and may require removing the wheel and drum to access. Use a wrench to turn the adjusting bolt clockwise to tighten the brake until the desired tension is achieved, then reassemble the wheel and drum. Always test the brake after adjustment to ensure proper functionality.
Remove a rusty rear brake drum on a 1975 corvette?
Better hope it is not a drum brake- it was originally equipped with a disc brake caliper.
Does the 1993 Camry have rear brake pads?
Take the wheel off to see if you see a caliper for a disc brake or a drum for a drum brake.
How do you get the rear brake drum off a 2005 Toyota Tundra?
There are two holes in the rear brake drum on the face of it that are threaded, they will be across from eachother. Find the correct thread bolt and screw them into the drum. They will push the drum out and away from the axle. Screw them in evenly a little at a time and use a rubber mallet if needed to pound around the drum to help it off. Sorry I am not sure of the proper bolt thread, I just looked through my can of bolts until I found two that fit. Hope that helps! The correct bolt size is M8 x 1.25 thread, I used one 35mm Long.
