0
The engine number on an RB30 engine is typically stamped on the engine block, usually located on the passenger side, near the front of the engine, just above the oil pan. It may also be found on a flat surface near the timing cover. Check the area around the cylinder head and the block for visibility, as it can sometimes be obscured by other components.
What else can I help you with?
Does a rb30 engine mounts match a rb25det?
yes they do
how much does an Nissan RB30 engine weight?
RB30 engine weight. ... top calculate the weight of the crate...Im assuming the Engine minus exhaust man & rocker gear is around 150kg mark.
Will a R32 R33 R34 inlet manifold fit a Rb30?
No, a Nissan R32, R33, or R34 inlet manifold will not directly fit onto an RB30 engine. The RB30 has a different design and specifications compared to the RB26DETT and RB25DET engines, which the R32, R33, and R34 manifolds are designed for. Modifications may be required to adapt an RB26 or RB25 manifold to an RB30, but it is not a straightforward fit.
Changing a timing belt on a Nissan rb30 engine?
why not get yourself a service manual and read the step by step instructions!?
How much horse power does a vl commodore have?
Well I had a look on wiki and it said the stock VL Commodore has a Nissan RB30 engine and it makes around 170 HP.
How much oil in rb30 gq engine?
The RB30 engine typically holds around 5 to 6 liters (approximately 5.3 to 6.3 quarts) of oil, including the oil filter. It's important to check the owner's manual or specific service documentation for your vehicle, as the exact capacity can vary slightly based on modifications or specific configurations. Always ensure to use the recommended oil type and grade for optimal performance.
How do you remove camshaft thrust plate from RB30 motor?
remove the seal and slide it to the side
How to remove a RB30 crank pulley?
Use a rattle gun if the engine is out. If its still in the car disconnect the disributer. Put a powerbar and socket on the pulley and lean on the xmember. Crank the engine over over for a split second. Heaps more info on forums. Google it or look on the gtr forum.
What are the torques for the Nissan RB30 main caps rod caps and head bolts?
38ft/lb for the mains
Can you just bolt on a turbo to a stock RB30 motor on a R31 Skyline?
u can bolt a turbo on a standard rb30, but yes it will prematurely destroy the engine, You should really rebuild the engine for it but at the very least, you should take the head off and have it re-faced and o-ringed and then install it back on with a decompression plate (available from repco). You should only do this to a motor that is in good nick to begin with, Its a bit silly to get an old engine with 300,000 k's on it and make it work harder all of a sudden. After the turbo's bolted on make sure the timing is NO MORE than the stock amount (i think its 15' btdc for an RB30). and use premium 98 octane fuel, This should eliminate any Detonation issues, But to be sure, you should check audibly by stopping on a steep hill and then flooring it to put the motor under load and listed for any pinging. Change the exhaust to at least 2 and a half inches and use a high flow cat and mandrel bends. You will not need any back pressure in the exhaust anymore because the turbo will provide this for the engine now. Start with low to moderate boost (maybe 6psi). and you should be tyre frying with decent reliability. Need any more info ask me. Cheers
Where is the engine number on a b15 engine?
where us the engine number of toyota avalon
Is the chassis number the same as the engine number?
short awnser No, but you can look it up if your chassis number and engine number are original or if its a diffrent engine
