answersLogoWhite

0

it matters if you make a hole in the door, if you do, you can, if you don't, you cant, then no one can it matters if you make a hole in the door, if you do, you can, if you don't, you cant, then no one can it matters if you make a hole in the door, if you do, you can, if you don't, you cant, then no one can

User Avatar

Wiki User

16y ago

What else can I help you with?

Related Questions

How do you open the rear hatch of a 97 Ford Expedition from the inside when the handle does not work and the door is locked shut?

remove the inside trim or cut a hole to reach the mechanism and replace the inside trim.


How do you drill for a door handle?

use the template that comes with the door handle read the instructions until you understand them measure three times cut once.


How do you repair a car door handle that is broken on the outside?

from the inside. take your door panel off and look around in there. the door handle is usually held on with pop rivets that have to be cut off from the inside of the door.


How do you change the glass of a window of a car?

door glass- you have to removed interior door handle, door panel to get access to the bolts that attach the glass to the window regulator. then the glass is pulled up and out. rear window and windshield- the glass is cut out with special tools and the new glass is glued in.


How do you open a 2004 Ford Transit van side door when its jammed shut?

Had the same trouble with a Toyota Tarago, door was locked and unable to unlock. So had to cut hole on external of door to unlock.


How do you get keys out of a locked trunk of a 1991 cadillac deville?

take vin # off title to dealer, they can cut you a key or if door is unlocked, depress trunk button switch


How do you surpass a locked door on a mobile home?

Same way you would in a regular house ! - Remove the lock or hinges if possible, if not, cut the lock off . Locks are cheap.


How do you remove the outside door handle 1997 ford thunderbird?

Tough task... Door handle is riveted to door so you'll need to drill out the rivets. These are replaced with flat head machine screws and lock nuts. I had to shorten one of the screws to allow the window mechanism to go by when rolling the window up or down. Need to remove the inner door panel to get to the inside of the door. Previous steps are easy. Toughest part is rod that connects the handle to the latch. You cannot get your hands in there to access it. I cut the old handle apart to get it out. I had a rod from the replacement handle that I modified to make it easier to install. I decreased the radius (unbent) of the bend where it enters the handle so it would slide into the handle easier when it was installed in the car. Also remember to disconnect the battery or the theft system will start blowing the horn in the middle of the job...I should know. I did this job on my car but it was not easy. Took several hours.


What is the best way to install an access door in a wall?

The best way to install an access door in a wall is to carefully measure and mark the desired location, cut out the opening using a saw, attach the access door frame securely to the wall, and then install the door panel into the frame. Make sure to follow the manufacturer's instructions and use appropriate tools for a precise and secure installation.


How do I replace door handle on a 2006 ford explorer?

Recently broke exterior door handle (door froze) on my explorer. I ordered the handle through dealership ($146) then painted the handle. To remove the door panel there are two snap on caps that must be removed first, one on the handle and one next to the latch. Pull off the cap/panels then remove screws plus one screw at very bottom of panel. To get the panel off you need to pull hard in out and upwards direction to get snaps off. There will be a cable that connects to your latch that can be remove with needle nose pliers. Also there is an electric cable with a snap connector. Push in the tab and pull the connector apart. Cut off the foam backing to access the inside of the door. Remove both nuts holding on handle. Open yellow tab that is on the threaded rod with a pair of pliers (this piece hinges). Remove handle (you may want to remove rod first) replace with new handle and repeat steps in reverse.


How do you replace an exterior door handle on a 1995 Honda Civic?

1) Purchase a new door handle from your local auto parts store or dealership. Which ever is cheapest is my preferance. 2) There are three Philips screws to remove. A)One in the handle to close the door, B)One in the door handle to open the door from the inside and C)One plastic screw at the front part of the door panel. Remove the plastic insert after removing the plastic screw. 3)You will need to remove the window crank by prying or pulling a pin from in between the crank and the door panel. Be careful not to loose the pin for they tend to fly very easily. Don't be scared to press the crank and panel apart. 4) Once the screws are removed the door is only held in place by Panel Pins. Pull the door panel away from the door. After the panel is loose lift the door panel off of the door. 5) Carefuly remove or cut the plastic wrap from the top outer corner of the door. Look for the opening that would face the back side of your outer door handle. 6) Once you have access to the handle you will need a 10mm socket and rachet to remove the old and reinstall the new handle. 7) There is another pin holding you Locking/Key assembly to the handle. Remove and pull the assembly away from the handle. 8) The rod can be a little tricky but your new handle should have a new plastic bushing for atachment. Pry the rod from the handle, you might need to wedge the old bushing apart to release the rod easier. 9) Once Removed do all the steps in reverse..


How do you capture the drapion on team dim suns ship?

go to the dark room on the cargo ship,get a level two cut and a flash pokemon,go to the locked door after you cut the Barlow free and Barlow should help you from there if he does not you'l figure it out.