answersLogoWhite

0

That would be not a good thing to do. Have it towed to a garage for repair.

User Avatar

Wiki User

12y ago

What else can I help you with?

Related Questions

How do you install brake pads?

1) remove Wheels 2) Loosen Caliper mounting bolts 3) Remove one caliper mounting bolt completely 4) Re-install 2 lug bolts to hold disk in place 5) swing caliper either up or down depending on which caliper bolt you have removed 6) use "c" clamp or similar tool to retract piston in caliper 7) install new pads 8) re-install caliper bolts 9) re-install wheel


2001 Buick lesabre front caliper mounting bolts which one goes top or bottom there is a difference in them?

The top (or leading) pin bolt uses the plastic bushing, the bottom bolt should be solid. Here is a snipet from a manual.Install the caliper over the rotor and onto the caliper bracket. Ensure that the caliper pin boots are not pinched. NOTE: The leading caliper pin, or top pin, has a bushing as part of the assembly. The trailing caliper pin, or bottom pin, is a solid design.Install the new caliper pin bolts (1) and tighten them to 70 lb ft (95 N.m). NOTE: It is important to note which caliper pin is designed for the correct bore. The leading caliper pin, or top pin, has a bushing as part of the assembly. The trailing caliper pin, or bottom pin, is a solid design. Ensure that the bolt boots fit securely in the groove of the pin bolts. Be sure not to pinch or tear the boots. If the boots are damaged, they must be replaced.


What is the brake hose connected to the caliper on a 98 GMC Jimmy called?

Rear brake hose, but their are 2 models. 1 is RJ2 that has a banjo bolt.


How do you remove rear caliper on 2006 Malibu?

1. Remove the brake hose to caliper bolt from the brake caliper. 2. Remove the brake hose from the brake caliper. 3. Remove and discard the 2 copper brake hose gaskets. These gaskets may be stuck to the brake caliper and/or the brake hose end. 4. Cap or plug the opening in the brake caliper and the brake hose to prevent fluid loss and contamination. 5. Remove the 2 brake caliper pin bolts. Remove the park brake cable from the caliper. 6. Remove the brake caliper from the brake caliper bracket.


What a three things a vernier caliper measures in a garage?

1. A shaft diameter 2. Length of bolt 3. Inside of a hub


How do you replace brake pads on 1992 Subaru legacy?

remove the wheel cover if it has one and then take and loosen the lug nuts 3/4 socket or 19mm, raise front of the car and support with jack stands. Finish removing the lug nuts and wheels. The caliper has only one lower bolt that is a 14mm, use a 1/2 inch drive and a breaker bar and loosen and remove bolt, the caliper should now pivot up from bottom and you can remove the pads. You will now want to open the hood and check the reservoir and and make sure that it does not over flow as you compress the piston in the caliper, a turkey baster works well to remove excess fluid. With a c-clamp(6inch) or a brake piston compressor you need to put the piston all the way back into the caliper. You can now pivot the caliper back over the new pads and reinstall the 14mm bolt. tighten the bolt to spec. and replace wheel etc. Pump the brake pedal a few times and check master cyl. level.


Changing rear brake pads on 2002 Mazda protege5?

The rear brakes on the P5 are a bit different than most setups...be careful! The only way to move the piston back into the caliper is by way of a special Allen head bolt that is directly behind the piston, on the back side of the caliper, installed under a 14mm bolt. You have to remove this bolt to gain access to the Allen head. As you loosen the Allen head bolt(counter-clockwise), the piston will move back into the caliper. Installation is pretty typical, again, the Allen head bolt being the unusual part. The manual says to tighten this bolt until the pads contact the rotor, then loosen the bolt 1/3rd of a turn, then reinstall the 14mm bolt. Hope this helps...I found all of this out the hard way.


What if 1 mount bolt breaks from being old while screwing will the car still crank?

If you have a broken bolt, the car is not safe to drive.


How change brake pads sc400?

loosen lug nuts. raise vehicle. remove wheel. remove 1 bolts on caliper. flip caliper open because one bolt is out it will sway freely. push back pistons to avoid having to bleed brakes. swap pads. then close caliper and secure bolt. put wheel back on. tighten lugs. lower vehicle on jack. torque lugs to 78 lbs.


1997 dodge ram front drive shaft bolt size?

1 and 11/16 in


What 4l60e has a 6 bolt transfer case?

The 1 THAT WAS MADE FOR A 4-WHEEL DRIVE 2 and 4 wheel drive transmissions are different.


Replacing Front Pads and Rotors on 2001 Grand-AM?

Remove wheels Re-Install 2 lug nuts to secure rotor Loosen 2 caliper mounting bolts Remove 1 caliper mounting bolt to allow caliper to swing out Remove outer brake pad Use "C" Clamp and inner brake pad to retract piston into caliper Install new brake pads (inner & outer) Remove 2nd caliper mounting bolt Remove caliper Remove 2 lug nuts and rotor should pull off Support caliper so it doesn't stress flex brake line After re-installing remember to PUMP BRAKE PEDAL TO SET PADS AGAINST ROTOR PRIOR TO MOVING VEHICLE