0
While many epoxies will claim to bond many things I would start by testing a small piece in a inconspicuous area. Clean concrete is a must.
Don't be lured by the quick setting versions of epoxy in the hardware store. In my experience the 90 min-4 hr types will bond best.
If your test fails and the epoxy stays on the concrete, try passing a flame over the surface of the rubber (be careful not to melt or burn it). Use proper safety instructions and do it outside. In many cases this will open the surface to the adhesive.
Special Polyurethanes (caulking or liquid) may also be useful for this application. Urethane is more flexible and may survive the traffic effect better. An added plus is they like to bond to concrete
What else can I help you with?
You bought a 16ft kit garage door storm shield threshold and went to lay it and the adhesive will not come out of the tube we tried everything The adhesive must not be good How do you get it replaced?
Take it back to where you bought it !
Where can one purchase a garage door threshold?
One can purchase a garage door threshold from Garage Door Fitters, Home Depot, Amazon, Wickers, Weather Stop and eBay stores. A garage door threshold helps to prevent rain that is driven by wind, dust, snow or dirt from getting under your garage door. This helps make your garage remain very clean and dry.
How can I replace the exterior door threshold on a concrete surface?
To replace the exterior door threshold on a concrete surface, you will need to remove the old threshold, clean the area, apply adhesive, place the new threshold, and secure it in place with screws.
What are the steps involved in front door threshold replacement?
The steps involved in front door threshold replacement include removing the old threshold, cleaning the area, measuring and cutting the new threshold to fit, applying adhesive or sealant, and securing the new threshold in place.
How can I replace a door threshold on concrete?
To replace a door threshold on concrete, you will need to remove the old threshold, clean the area, apply adhesive, place the new threshold, and secure it with screws. Make sure the new threshold is level and fits properly before finishing the installation.
How can I effectively install a garage door water barrier to prevent water damage and leakage?
To effectively install a garage door water barrier, start by cleaning the area around the garage door and ensuring it is dry. Next, apply a waterproof sealant or adhesive weatherstripping along the bottom of the door to create a tight seal. Additionally, consider installing a garage door threshold seal to further prevent water from seeping in. Regularly inspect and maintain the barrier to ensure its effectiveness in preventing water damage and leakage.
What are the best ways to seal the top of a garage door gap effectively?
To seal the top of a garage door gap effectively, you can use weatherstripping, a garage door threshold seal, or a garage door seal kit. These options help prevent drafts and keep out pests and debris.
How can I remove a door threshold?
To remove a door threshold, you can start by using a pry bar to gently lift and loosen the threshold from the floor. Then, carefully remove any screws or nails securing the threshold in place. Once the threshold is free, you can lift it out and clean up any remaining debris or adhesive.
How can I install garage door sensors?
To install garage door sensors, first locate the appropriate placement for the sensors on each side of the garage door. Then, mount the sensors securely using screws or adhesive. Connect the sensors to the garage door opener according to the manufacturer's instructions. Test the sensors to ensure they are working properly before using the garage door.
How can I effectively perform a door threshold repair to ensure the durability and functionality of my entryway?
To effectively perform a door threshold repair for a durable and functional entryway, follow these steps: Remove the old threshold carefully. Clean the area thoroughly to remove any debris or old adhesive. Measure and cut the new threshold to fit the doorway. Apply a waterproof sealant to the bottom of the new threshold before installing. Secure the new threshold in place using screws or adhesive. Test the door to ensure it opens and closes smoothly. Apply a final coat of sealant to protect the threshold from moisture and wear.
How can I prevent water from entering my garage through the gap under the garage door by installing a seal?
To prevent water from entering your garage through the gap under the garage door, you can install a weather seal or threshold seal along the bottom of the door. This will create a barrier to keep water out and help maintain a dry garage interior.
What adhesive would you use to bond the external glass of an oven door to the metal door of the oven?
Ask in the hardware store for an adhesive that has extremely high heat resistance.ANS 2 A good high heat epoxy, such as J B Weld.
