0
What else can I help you with?
How do you disconnect the power antenna on a 1988 Cutlass Cierra?
Just unplug the power wire below the motor or the fuse in the fuse box..
How do you remove the power antenna on a 1996 Infiniti I30?
Open up the truck.. Unplug power line but, don't unplug the antenna line. It's will be used for your remote. - brokenics@yahoo.com
Where would you find the plug to unplug the power antenna on a 1991 Cutlass Ciera?
Mounted to a relay thats screwd in to the plastic glovebox. just open it unscrew the screws and take it out and you will see the relay attatched to the glovebox.
1993 Oldsmobile cutlass supreme power antenna will not turn off or go down?
First physical pull the antenna all the way up, clean the antenna very good with a degreaser, then lubricate it with a silicon spray. Open the trunk, unplug the power to the antenna, start your car with the radio turned on, stop the engine, plug the power source to antenna back in. Try it now, if you still have the same problem, either the relay is stuck and needs replacing or the antenna motor is shorted and needs to be replaced.
Which power antanna was used on a 1989 Cutlass Supreme?
Check your RPO codes. If it has an U75 than it had a power antenna. If it has RPO code US6 it has a painted fixed antenna. There was only one style power antenna used from the factory.
If your power antenna on a '91 lesabre jams up but the motor keeps trying to make it go down how can you stop the motor and fix the antenna?
unplug the electrical from the antenna. replace antenna.
How do you disconnect antenna power on a 1990 cutlass ciera?
To disconnect the antenna power on a 1990 Cutlass Ciera, first, locate the antenna assembly, which is usually found at the rear of the vehicle. Remove any trim panels if necessary to access the wiring. Then, disconnect the power wire from the antenna motor, typically a small connector or plug, ensuring the ignition is off before handling. Finally, if you need to remove the antenna, unscrew it from its base and pull it out gently.
1989 cutslas and the power antenna motor keeps running and the antenna is stuck in the up position What do you do?
If the antenna is in the up position, you have 2 options, replace the entire assembly, or unplug it. In the trunk under the antenna, you will find a set of 3 wires going into a relay. Unplug those, and the motor will turn off.
Antenna wiring dighram for a 1997 olds cutlass supreme?
To create an antenna wiring diagram for a 1997 Oldsmobile Cutlass Supreme, you typically need to reference the vehicle's service manual for specific wire colors and connections. Generally, the antenna wire is connected to the radio's antenna input, while the power wire for a power antenna (if equipped) connects to the radio's power antenna lead. Additionally, ensure proper grounding for the antenna system. If you need precise details, it's best to consult a wiring diagram specific to that model year.
Replace the power antenna on your 1994 sable wagon?
the power antenna is located on right front. I jacked my car, and removed the right front wheel. Then there are some small screws which are keep the inner fender plastic. unscrew them. You can reach with your hand the power antenna. Unplug the power wire, and the antenna wire, and unscrew those small (8mm) screws which are holding the antenna in its bracket.
How do you remove and replace a power antenna on a 1998 corvette?
To remove and replace the power antenna on a 1998 Corvette, first, disconnect the negative battery terminal to ensure safety. Then, access the antenna by removing the rear interior panel where the antenna is located. Unplug the antenna harness and unscrew the antenna from its mounting bracket. Finally, install the new antenna by reversing the steps, securing it in place, and reconnecting the battery.
1992 cutlass ciera radio antenna whirrs and bobs up and down after the engine is turned off The battery will run down unless I unplug the battery How do I fix this?
Try turning the radio off before turning the car off. If this doesn't work, check the assembly at the base of the antenna for a sensor switch for gunk and clean it off. Don't ask me where it is, because I don't have the schematics for the antenna assembly on a 1992 Cutlass Ciera handy at this moment. If this doesn't work, the easiest "fix" is to wait until the antenna goes all the way up, then clip the power lead to the antenna motor. Just make sure you don't clip the antenna lead. This will keep the antenna up all the time. Next cheapest route is to replace the whole antenna assembly, motor and all. I would recommend getting a cheap $5 standard antenna from a local auto parts store and do away with the "convenience" of the automatic retractable antenna.
