answersLogoWhite

0

What else can I help you with?

Continue Learning about Basic Math

What is the difference between exit and close commands?

In computing, the "exit" command is typically used to terminate a program or a process, while the "close" command is used to shut down a file or a resource that is being used within a program. When you use the "exit" command, you are ending the entire program, whereas the "close" command is specifically used to release a specific file or resource that was previously opened or accessed. Essentially, "exit" is for ending the program, while "close" is for closing individual components within the program.


What is the difference between a variable and a constant?

A constant cannot be changed by the program while it is running. Furthermore, it does not take up any memory on the stack or in the heap, as it is inlined into the compiled code during the compilation process. They are used to represent unchanging data, such as the value of PI, or the date that a particular function was written. A variable is a memory location or register value that may be modified during the execution of the program, and represents data that is unknown until the program runs. Examples might include today's date, the number of times the user has logged in, or the user's preference in colors.


How do you fix packet tracer 9.9.1.3?

Fixing packet tracer 9.9.1.3 can be done by running a diagnostic on that program. However if the diagnostic does not work, a simple restarting or uninstalling and reinstalling the program may be beneficial.


What the Difference between accumulator and register?

The accumulator is a general register that holds a value. It is also a special register that can be used as the target for the result of various arithmetic or logical computations. For instance, if you wanted to add two numbers, you could load the first into the accumulator, add the second to the accumulator, and then store the accumulator where wanted. The instruction register is an internal register that holds the value of the instruction opcode in order for the 8085 to decode and process the instruction. While it is shown on the Intel block diagram for the 8085, it is not directly accessible by the running program - it is for internal use only by the 8085.


How do you completely delete data beyond retrival?

You can always use a free program calledEraser.This option however is only available for PC users running Windows.The software is open source and can be downloaded from its own web site at http:/eraser.heidi.ie

Related Questions

What is the difference between an active application and an icon?

The difference between an icon and active application is that an icon is a small image seen on a computer screen and it represents a program but is not running. An active application is one that is running in the foreground of a computer.


What is difference between running and walking?

You get to mcdonalds faster running


What is the difference between a process and a program?

A program is a set of instructions that tell a computer what to do, while a process is an instance of a program running on a computer. In simpler terms, a program is like a recipe, and a process is like the dish being cooked according to that recipe.


Does your downloading carry-on on bittorent if you switch off your computer?

No. When your computer is off, no program is running which means bittorent isn't even on to download anything.


How does a person run a computer analysis?

Running a computer analysis requires downloading a free program such as System Analyzer. This program will look for increasing speed, disk space, system security, and many more things to get your computer in good running condition.


How can one use the program 'Nitro PDF'?

One can use the program 'Nitro PDF' by downloading it to their computer, following the installation instructions, and then running the program. One should check that they agree with the Terms of Service and that their computer meets the requirements to run such a program.


What is the difference between an earthtquake and a fault?

The same as between running and legs.


What is the exact difference between interrupt handling and exception handling?

interrupt handling is the process of handling a break or interrupt called by a program where as exception handling is for handling some exceptional conditions that'll occur when a program is running


What is difference between stop and end in GWbasic?

The end command is used to end the program whereas the stop command is used to break the loop like ctrl+c. After running the program it will come as break in 20 or whatever


'What is the difference between multiprogramming and multitasking and what is meaning of a task if we consider a task as a program then the concept will be multiprogramming then what is the differenc?

First of all there is difference between program and a task. There may be multiple tasks running related to one program at the same time. so if the processor is busy in multiple tasks related to one program then it is multitasking. But if the multiple tasks which the processor is executing concurrently are related to different independent programs then the concept is know as multiprogramming.


What is the iphoto download process?

The process for downloading the iphoto program is simple. First you need to have an Apple computer running Mac OS X. Then go to the Apple website and click iphoto download. Then run the program.


What is the difference between running feet and square feet?

1100