0
What else can I help you with?
How many 2x4s are in a unit of lumber?
A standard unit of lumber, often referred to as a "lumber unit" or "board foot," typically contains 1,000 board feet. Since a 2x4 measures 1.5 inches by 3.5 inches and is usually 8 feet long, it equals 5.33 board feet per piece. Therefore, a unit of lumber contains approximately 187 pieces of 2x4s, assuming standard lengths and no waste.
How many board feet to build a 3000 square foot house What would the average total cost of the lumber be?
30,000 board feet. Today $350 per thousand board feet, it will cost $10,500.
How many 3 foot pieces could you get out of two boards that are 12 inches long?
Each board is 12 inches long, which is equivalent to 1 foot. Therefore, two boards would total 2 feet in length. Since a 3-foot piece cannot be obtained from a total of 2 feet, you cannot get any 3-foot pieces from the two boards.
How many square feet in a 2x5.5x12 board?
To calculate the square footage of a board, you multiply its length by its width. For a board that is 2 inches wide and 5.5 inches tall with a length of 12 feet, first convert the dimensions to feet: 2 inches is approximately 0.167 feet and 5.5 inches is about 0.458 feet. Then, the square footage is 0.167 feet (width) x 12 feet (length) = 2.004 square feet.
How many board feet is 4' x 8'?
To obtain the board measure multiply the length in feet to be covered by the width in feet. If the boards are over one inch thick multiply this by the thickness in inches. Thus assuming the boards are 1 inch thick or less the board measure is 4 x 8 = 32 feet board measure (B.M.)
Dustin has a board that is 12 feet long. he cuts three pieces that are each 3 feet 9 inches long.how many inches are left over.?
He would have 9 inches left.
A board 8 feet 6 inches long is cut into 3 pieces How long is each piece?
8 feet 6 inches = 102 inches. If the three pieces cut are equal in length then each would be (102/3) = 34 inches long (not accounting for material wasted in the cutting process).
How can I make a cutting board from a log?
To make a cutting board from a log, you will need to cut the log into slices, sand the slices to create a smooth surface, and then seal the wood with food-safe finish. You can also add a handle or feet to the cutting board for convenience and stability.
Cutting a 10 foot plank into 10 equal sections if it takes 1 minute per cut how long will it take him to get the 10 equal pieces?
NOTE: The problem asks to cut the board into 10 equal parts, not into equal boards proportional to the original piece of wood. Case 1: CANNOT stack wood on top of each other. Assume the board 5 feet by 2 feet. If you made one horizontal cut in the center of the board 1 foot from each edge, and then made four vertical cuts at 1 foot apart, you would then have 10 equal pieces at 1' by 1' each. Time taken: 5 minutes for 5 cuts. Case 2: CAN stack wood on top of each other. The board is 5 feet by 2 feet. Cut the board long way 1 foot from the middle and the result is 2 boards 5 feet by 1 foot. Stack these two boards on top of each other. Then, cut the stack vertically one foot from the end now making 2 pieces of wood 1' by 1' and 2 pieces of wood 4' by 1'. Then, take the 2 pieces of wood 4' by 1' and stack them on top of each other. Cut vertically once in half, so you now result in 4 boards 2' by 1'. Finally, stack these 4 pieces of wood on top of each other. Cut once vertically and you now have 8 pieces of wood 1' by 1' (plus the 2 from earlier which now make 10). Time taken: 4 minutes for 4 cuts.
How many pieces of sheet rock comes in a pallet?
A pallet is 500 square feet. Sods vary in size according to who cuts them.
How many 10 inch pieces can be cut from a board that is 12 feet long How much is left over?
14 pieces. 4 inches left over.
How many 10 inch pieces can be cut from a board that is 12 feet long?
1 foot = 12 inches so 12 feet = 12*12 = 144 inches from which 14 10" pieces can be cut.
Jason is building a bench with his dad. He begins with a 8 foot board. Then, he cuts off a piece that measures 3 5/8 feet and another that measures 1 1/3 feet. What is the length of the remaining board?
3 1/24
How many pieces of 2x6x12 does it take to cover 1000 square feet?
To determine how many pieces of 2x6x12 boards are needed to cover 1,000 square feet, first calculate the area of one board. A 2x6 board is actually 1.5 inches by 5.5 inches in dimensions, which equals 0.0625 square feet per board (1.5/12 * 5.5/12). To cover 1,000 square feet, you would need approximately 16,000 boards (1,000 / 0.0625).
How can I create a live edge cutting board?
To create a live edge cutting board, start by selecting a piece of wood with a natural edge. Cut the wood to the desired size and shape, making sure to preserve the live edge. Sand the board to smooth out any rough edges and apply a food-safe finish, such as mineral oil or beeswax, to protect the wood. You can also add a handle or feet to the cutting board for added functionality.
Is there something like the wave board but there are two separate pieces for your feet?
some people have them that they made themselves. but the best of the brand-name castor boards is the wave board hands down.
A 42 foot board is cut into two pieces. Four times the shorter piece is equal to the sum of the longer piece and thirteen. Find the lengths of both pieces.?
Using algebra it works out that the lengths are 8.4 feet and 33.6 feet because 4*(8.4) = 33.6 and 8.4+33.6 = 42 feet
