0
What else can I help you with?
What joints are used when bowling a cricket ball?
When bowling a cricket ball, the main joints used are the shoulder joint, elbow joint, and wrist joint. The shoulder joint provides power and rotation, the elbow joint controls the release and accuracy of the ball, and the wrist joint imparts spin and deviation. Coordination among these joints is essential for a successful bowling action.
If you change upper ball joint should you change the lower ball joint too?
It's not always necessary to change the lower ball joint when replacing the upper ball joint. However, it's recommended to inspect the lower ball joint for any signs of wear or damage while working on the upper ball joint. If the lower ball joint shows signs of wear, it may be a good idea to replace it to ensure optimal performance and safety.
What is The junction line where two bones form a joint that does not permit any movement?
A joint that does not allow any movement is called a synarthrosis joint. This type of joint can be found in the skull, where two bones have a suture line that is immovable. An example is the joint between the two parietal bones of the skull.
What is the joint above and below the knee?
It is not a separate joint it is your hip joint, the hip joint is a ball & socket joint!!!
Is the knee joint a pivot joint?
No, knee joint is a compound joint (condyloid joint between tibia and femur and saddle joint between femur and patella).Yes, there is a pivot joint in the knee. Pivot joints can also be found in a person's neck, forearms, and other parts of the body. This is because the pivot joint moves by rotating.The knee is mainly a hinge joint not a pivot joint.
How do you replace a rear you joint in a 1999 Chevy Astro van?
Unbolt/remove driveshaft. Use U-joint press to remove old U-joint, install new and replace driveshaft.
How do you replace a u- joint on a Ford Ranger?
how to replace u-joints on 1995 ford ranger 2wd
1999 dodge1500 4x4 front hub you joint i have it all apart but cant get u joint knuckle free so i can replace iner and outer bearings can you help me?
Watch this video on how to replace a u-joint to see if it helps. http://www.myjeepwrangler.com/ Fix-it > u-joint
How to disassemble a CV joint in a 1989 Bronco The enclosed 2 U joints by the Transfer Case with the ball joint.?
I am not 100% sure what the question is, but here is a shot at it. If you are trying to replace the u-joint, there is a video at myjeepwrangler.com under Fix-it > u-joint
Popping sound underneath car feels like something wrong with the driveshaft what is wrong?
Check the U joints. answer opping sound indicates a dry u joint if its not to late , grease the joint if that doesnt fix it, replace the u joint
How do you replace the u joint on a 1995 Buick Roadmaster drive shaft?
very carefully!
How do you replace a 325E U-joint?
not possible. the whole drive shaft needs replaced.
How do you replace the CV joints on a Toyota Celica GT?
pull the drive line, pop the caps off the u-joint, and drive the u-joint out of the drive-line and install the new one.
How do you change the center you joint on a 1958 impala?
On a 1958 Impala you change the center U joint you need to first place the car on jack stands. Next, remove the bolts or straps holding the U joint cross in place. Once removed, replace with the new center U joint and bolt back in place.
A lot of noise from U joint on 87 bronco 2it is a CV U joint any help?
has front end been lubed lately? if it has, then u need to pull cv joint apart and replace worn parts. it is an easy job if you have a shop manuel as well sometimes it is not the cv joint but the locking hubs. that is easier job than a cv joint
How do you replace upper ball joint on a 98 ranger?
u can't just change the upper ball joint, u have to change the whole upper control arm. It is welded to the arm in one piece.
Replace cv joint on Lincoln LS?
don't replace the joint. replace the axle
