0
What else can I help you with?
How do you replace a rear wheel bearing 2001 Prius?
Remove tire, remove brake drum, remove brake assembly housing, remove 4 bolts from back of hub assembly, gently tap to remove hub/bearing assembly.
How do you change a 70 HP Yamaha outboard water pump?
The water pump on an outboard motor is located low down on the skeg. To replace it, you have to remove the lower unit. The impeller water pump is a housing attached to the upper unit, surrounding the shaft. It must be replaced exactly right, so obtaining a proper servicing manual is strongly recommended.
How do you remove the Clutch Release Bearing Lever Arm on a golf MK3?
You will remove the engine then you replace the clutch plate on the flywheel, You also will have to remove the bearing which sits in the bell housing, and then put it back together again.
How do you change a jackshaft bearing on a 2004 Yamaha RX Warrior?
To change the jackshaft bearing on a 2004 Yamaha RX Warrior, start by removing the track and drive system to access the jackshaft. Next, remove the jackshaft from its housing by taking out the retaining clips and any fasteners holding it in place. Replace the old bearing with a new one, ensuring it is properly seated, and reassemble the jackshaft in reverse order. Finally, reattach the track and drive system, ensuring everything is secure before testing.
How do you change rear pinion bearing on a 2004 dodge 1500 ram 4x4?
1. remove rear drive shaft.2.remove diff.cover.3.remove both axles.4.remove carrier case assy.5.remove drive shaft yoke.6.tap pinion gear out of housing with (brass hammer).7 remove pinion seal and front pinion bearing.8.rear pinion bearing well need pressed off & on the pinion gear.9.you need to use a punch drive the bearing race from housing both.
How do you remove rear wheel bearing from axle 1989 Mazda b2200?
To remove the rear wheel bearing from a 1989 Mazda B2200 axle, first, safely lift and support the vehicle, then remove the rear wheel and brake drum. Next, detach the axle shaft by removing the retaining bolts or nuts and slide the axle out. Use a bearing puller or a suitable tool to carefully extract the bearing from the axle housing, ensuring not to damage the housing. Finally, clean the area and replace the bearing with a new one, following the reverse steps for reassembly.
How do you change rear axle brearing on a suzuki quadracer?
You only need to remove the left hub assembly. Loosen the axle nut while still on four wheels. Having said that, put rear on suitable stand forward of the rear axle bearing carrier. For ease remove both rear wheels. Remove drive chain. Remove left hub. Remove brake caliper and secure. Remove the rear sprocket with flange together. There are two nuts on the axle that holds this in place. The nuts are different. The outer nut is a lock nut. Remove the outer and remover the inner nut. You can now slide the axle shaft out of the bearing housing. Now remove the housing after loosening the retaining bolts. Take the housing to a bench and remove seals and bearing. Note that there is a long spacer separating the bearing which is in the middle. This how I did this on my 86. Regards
How do you change a 1996 Jeep Grand Cherokee rear wheel bearing?
How do you change a 1998 Jeep grand Cherokee rear wheel bearing you will have to remove housing in rear, break down axel, pull the side you are working on away from the wheel & replace bearing, it also requires a special tool to get into the housing case
I am replacing the wheel bearing on my 1999 dodge durango 4-4 how do i remove the bearing i have removed all the bolts but I still can't remove the bearing help fast I need my vehicl?
this is a sealed hub and bearing assembly. it should come with the "hub" the flange with the lug studs sticking out, and pressed into the bearing housing.. if u just received a bearing only.. u will need new seals and a press..
How do you replace a front wheel bearing on a 2000 Hyundai Sonata GXE?
AnswerRemove the wheel, and then remove the brake assembly then remove the rotor next you will have to remove the front axle. Once this is removed you will now be able to see the bearing now you have to remove the housing that the bearing is located in it should be 3 bolts that hold it in place once you get it free you then need to have the old bearing pulled out by a hydraulic press and then have a new bearing pressed in. Most machine shops are able to remove and press the new bearings in once the new bearing is in just reassemble everything. This is a time consuming project.
How do you remove the rear axle bearing on a 2000 Polaris Expedition?
To remove the rear axle bearing on a 2000 Polaris Expedition, first, safely lift and secure the vehicle. Remove the rear wheel and brake components to access the axle. Use a bearing puller or a suitable tool to carefully extract the bearing from the axle housing, ensuring not to damage any surrounding parts. Finally, clean the area before installing the new bearing.
How do you change the impeller on the water pump on your 35 horsepower evinrude outboard boat motor?
First, remove the lower unit (there is a housing for the water pump). The drive shaft goes through the housing and turns impeller. Remove the housing, the impeller is on the shaft. Install the new impeller. When replacing the housing, turn the drive shaft clockwise to make it slide down over the impeller.
