0
What else can I help you with?
How do you calculate the slope of a graph?
Using limits and the basic gradient formula: rise/run.
When there is no change in value from one data point to the next in a line graph what type of slope does the line that connects them have?
The slope is zero. Slope is rise over run, the rise is zero, so zero divided by anything is zero.
How many gas BTU in 1 inch pipe?
The gas BTU capacity of a 1-inch pipe depends on several factors, including the gas type, pressure, and flow rate. For natural gas at a typical pressure, a 1-inch pipe can carry approximately 100,000 to 150,000 BTUs per hour. However, this value can vary based on specific installation conditions and the length of the pipe run. Always consult relevant code tables or a professional for precise calculations.
What is a trend of a line on a cartesian coordinate plane?
The slope of a straight line is often described by the rise over the run. This is the ratio of the vertical distance between two points and the horizontal distance between them (taken in the same order).
What is the calculation to find the slope on a line graph?
Given the points A = (xa, ya) and B = (xb, yb), then the slope is(ya - yb)/(xa - xb) or, equivalently, (yb - ya)/(xb - xa).The equation is sometimes referred to as "rise"/"run".
How do calculate a slope of sewage pipe?
To calculate the slope of a sewage pipe, measure the vertical drop (rise) and the horizontal run of the pipe. The slope can be calculated using the formula: slope = rise/run. This value is often expressed as a percentage by multiplying the result by 100. For example, a slope of 1:100 means a 1% incline, where the pipe drops 1 unit vertically for every 100 units horizontally.
Can a drain pipe rise up and then down for a small portion of the run if the slope of the overall run is quite steep?
You can do this with something like a storm water pipe. Storm water is basically clean and there is unlikely to be any problem with build up of sludge in the pipe. You should not do it with sewerage pipe as it will cause it to block up eventually
Joel is laying pipe for sprinker system before he plants his lawn The lawn is a rectangle15 feet long and 8 feet wide He needs to lay a piece of pipe that will be run along the diagonal of the lawn.?
17 feet.
What does B.O.P. stand for in piping?
For horizontal run pipe it is Bottom of Pipe For vertical run Pipe it is back of pipe
How do you calculate rise over run?
rise divided by run: a fraction, rise is y and run is x (you run on a horizontal plane) (you rise on a vertical plane)
What size water pipe should you have to keep the pressure and volume the same as the water mains' to run 300' with a 30' rise?
there is no size of pipe to keep the pressure the same if your rise is 30' and the volume or flow will drop with any size pipe too at 300' but if you want the least amount of pressure drop and flow for the smallest pipe to save costs then depending on demand I would run 3" or 4" solid core PVC or if you have pressure greater then 80 psi I would run 2" black poly if its for 2.5 bath or smaller home.
How can you tell if a frozen pipe bursts if you have well water?
When the pipe thaws, the pump will run almost constantly. Watch your pressure gauge on the tank and if it will not rise, or has problem building pressure above 30 psi, then yo almost certainly have a broken pipe.
Joel is laying pipe for a sprinkler system in his lawn The lawn is a rectangle 15 feet long and 8 feet wide He needs a piece of pipe that will be run along the diagonal how long will the pipe be?
Using Pythagoras' theorem:x2 = 152 + 82x2 = 225 + 64x2 = 289x = sqrt(289)x = 17 feet long.
Is it rise over run or run over rise on a cordinate plane?
If you're talking about slope, it is rise over run. But why is it not the other way run over rise?
Slope is rise divided by run?
Yes, rise divided by run
Do you divide the rise over run or vice verse?
Rise over run
What is the change in rise divided by the change in run?
Rise/run is the slope of a line.
