0
What else can I help you with?
How do you calculate the louver vent size for return air required for an exhaust fan?
quick down and dirty way is the size of your unit (example..4 tons) X 144= the square inches needed for the return vent size or the longer way Max air flow from unit (rated size) / 2.08 cfm/sq in= filter area needed
How do you calcualte the optimal size of IPO?
How do you calculate the optimal size of an IPO?
How do you calculate rainwater runoff to determine culvert size?
To calculate rainwater runoff for determining culvert size, you first need to assess the drainage area, including its size and land use characteristics, which affect runoff coefficients. Utilize the Rational Method, where runoff (Q) is calculated using the formula Q = CiA, with C being the runoff coefficient, i as the rainfall intensity (in inches per hour), and A as the area (in acres). After determining the peak runoff, consider factors such as culvert slope, material, and local regulations to select an appropriate culvert size that can handle the expected flow without causing flooding or erosion.
What size return for a 100000 BTU furnace?
For a 100,000 BTU furnace, the recommended return air duct size typically ranges from 14 to 20 inches in diameter, depending on the specific design and layout of the HVAC system. The exact size may vary based on factors such as the length of the ductwork, the number of bends, and the overall airflow requirements. It's crucial to consult with an HVAC professional to ensure the proper sizing and efficiency of the system.
King vs. California King Sheets?
King size sheets will not fit on a Calfornia king size bed. The fitted sheet will fit but the top sheet will be 4" shorter. A king is 4" longer and a california king is 4" wider.
What size return grille for a carrier-48gp030060311?
To determine the appropriate size return grille for a Carrier 48GP030060311 unit, you'll need to consider the unit's airflow requirements and the size of the existing ductwork. Typically, the return grille size should match or slightly exceed the size of the return duct to ensure optimal airflow. It's usually recommended to consult the unit's installation manual or a professional HVAC technician for specific sizing guidance tailored to your system's configuration and airflow needs.
CALCULATE Supply air grille size for 900 CFM?
Wall Grille = 1050X200 SAG/RAG Linear bar Grille = 150mm HIGH LBG 3M - Suppy
How big should an air return be how many square inches per square foot of house?
Air return duct and filter grille size is dictated by the size of the unit (CFM) not the size of the house.
How much will a cold air return cost to have it added to your furnace?
The cost is determined by the size of the grille. $.40/square inch
How do you quiet the the air return?
If it is the airflow that is making the noise, this is caused by undersized ducts. If you recently had your equipment replaced be sure the airflow is set properly for the size equipment you have. If it is, look into increasing the return air grille size. That may give you some improvement. If the noise is still objectionable the duct size will probably need to be increased.
What is the size of exhaust air grille for 33000 cfm?
5000mmx1000mm..
What is the formula to calculate size of a sample?
by using the capture-recapture method which gives you the total size of organisms in a population.
How you would calculate the amount an object is magnified when using a microscope?
M=O/A magnification = observed size/actual size
What size should the return air filter grill be on a 2 ton unit?
The best rule of thumb I have found is: Length X Width / 144 * 288 = Max. CFM I have used this formula to size many HVAC systems. It has always worked. For example, a 5 ton unit should have a 30x36 grille(2-18X30 filters). (30x36)/144*288=2160 max cfm. Return Air should be sized at 200 square inches per ton according to AirMate and other filter grille manufacturers to achieve 2.0 static pressure. The Return Air Duct should have an unobstructed 6 square inches per 1000 BTU of cooling.
How do you calculate the louver vent size for return air required for an exhaust fan?
quick down and dirty way is the size of your unit (example..4 tons) X 144= the square inches needed for the return vent size or the longer way Max air flow from unit (rated size) / 2.08 cfm/sq in= filter area needed
How do you calculate the return air grillsize in an air conditioning system?
really depends on the size of the unit but if your not sure i would go with a 20x20 or a 20x25 filterback grill..
How do you calculate spanner size for nut?
How to calculate spanner size regarding bolts and nuts
