no
It is recommended to use about 3 tablespoons of copper sulfate for every 10,000 gallons of water in the pool. For a 16 by 32 in-ground pool, assuming an average depth of 5 feet, the pool holds approximately 15,000-20,000 gallons. Therefore, you would need around 5-6 tablespoons of copper sulfate for this size pool.
yes, just don't use too much I would not recommend using copper sulphate in a pool. It is an algaecide but it stains pools and is what causes hair to turn green. There are better algaecides available. It is not a sanitizer and is not a substitute for chlorine or bromine.
If you needed to use powered copper 2 sulfate in an experiment and were only supplied with clumps of copper 2 sulfate which tool would you need to convert the copper sulfate to usable form?
You would need to use a mortar and pestle to grind the clumps of copper (II) sulfate into a fine powder, making it easier to use in your experiment.
It is not recommended to use an iron spatula to stir a solution of copper sulfate as the iron can react with the copper sulfate solution and potentially contaminate or alter the solution. It is best to use a glass or plastic spatula for stirring solutions containing copper sulfate.
It is recommended to use about 3 tablespoons of copper sulfate for every 10,000 gallons of water in the pool. For a 16 by 32 in-ground pool, assuming an average depth of 5 feet, the pool holds approximately 15,000-20,000 gallons. Therefore, you would need around 5-6 tablespoons of copper sulfate for this size pool.
yes, just don't use too much I would not recommend using copper sulphate in a pool. It is an algaecide but it stains pools and is what causes hair to turn green. There are better algaecides available. It is not a sanitizer and is not a substitute for chlorine or bromine.
If you needed to use powered copper 2 sulfate in an experiment and were only supplied with clumps of copper 2 sulfate which tool would you need to convert the copper sulfate to usable form?
First of all I'm not a pool expert, but I've owned a pool for a bought 25 yrs. I live in Ohio and I have a 23,000 gallon vinyl liner pool with a sand filter system. First thing you need to do is make sure your alkalinity is at least 50 ppm. for copper sulfate to work properly. My pool used to be totally dark green when I opened it. I now use 2 table spoons of copper sulfate when I open it in the spring and it goes from green to clear in a bought 2 days. I also use the same amount in the fall when I close it, but make sure you circulate the water for 2 days before you close it. Make sure you mix the copper sulfate with water in a plastic container, make sure the blue crystals are dissolved. I use a 2 gallon plastic container with a sprinkler head on it like you use to water flowers with, this makes it easy to sprinkle the copper sulfate mixed with water in the pool evenly. You can buy copper sulfate at your local hardware store or on ebay. I'm sorry this information is so long, but I know what you're going through, because I've been through it. I hope this helps you. P.S. I only use use copper sufate in the spring and the fall. I do not use it during the season as a chlorine substitute as some people say they do, as to much copper in your water can cause you problems.
No
You would need to use a mortar and pestle to grind the clumps of copper (II) sulfate into a fine powder, making it easier to use in your experiment.
First of all I'm not a pool expert, but I've owned a pool for a bought 25 yrs. I live in Ohio and I have a 20,000 gallon vinyl liner pool with a sand filter system. First thing you need to do is make sure your alkalinity is at least 50 ppm. for copper sulfate to work properly. My pool used to be totally dark green when I opened it. I now use 2 to 3 table spoons of copper sulfate when I open it in the spring and it goes from green to clean in a bought 2 days. It may be a little cloudy at first, but when you get your alkalinity, chlorine, stabilizer, and PH where it belongs, it will clear up. I also use the same amount in the fall when I close it, but make sure you circulate the water for 2 days before you close it. Make sure you mix the copper sulfate with water in a plastic container, make sure the blue crystals are dissolved. I use a 2 gallon plastic container with a sprinkler head on it like you use to water flowers with, this makes it easy to sprinkle the copper sulfate mixed with water in the pool evenly. You can buy copper sulfate at your local hardware store or on ebay. I'm sorry this information is so long, but I know what you're going through, because I've been through it. I hope this helps you. P.S. I only use copper sulfate in the spring and the fall. I do not use it during the season as a chlorine substitute as some people say they do, as to much copper in your water can cause you problems.
It is not recommended to use an iron spatula to stir a solution of copper sulfate as the iron can react with the copper sulfate solution and potentially contaminate or alter the solution. It is best to use a glass or plastic spatula for stirring solutions containing copper sulfate.
Sulfuric Acid. The chemical reaction is Cu + 2H2SO4 = CuSO4 + SO2 + 2H2O
You would need a mortar and pestle to crush and grind the clumps of copper sulfate into a powdered form.
When copper sulfate is applied at the PROPER rates and proportionsthe water is supposed to be safe immediately for swimming. However, it does have an unpleasant smell, so waiting for at least 12 hours is advisable.
You would need a mortar and pestle to crush and grind the clumps of copper sulfate into a fine powder for use in your experiment. This tool will help you break down the clumps into smaller particles, making the copper sulfate easier to dissolve or mix with other substances.